0
What else can I help you with?
How can you clean the Idle Air Control Valve on a 1998 Nissan Frontier?
how can I clean the Idle Air Control Valve on a 1998 Nissan Frontier
What is making your Clio not start after short journeys?
Faulty TDC Sensor, All it will need is cleaning. Take it out clean the tip of the sensor so it is clean and shiny again, also clean the electrical connector.
If ABS light goes on and having error discontinuity on rear right sensor do you have to check the cable of the sensor or do you have to replace it?
You have to find the problem and fix it. If it's a connector, repair or clean the connector. If it's the sensor, replace the sensor. There are no "one size fit's all" repair answers.
How do you clean Mass air flow sensor on a 1998 Nissan Altima?
how do you clean mass air flow sensor on a 1998 Nissan altima? To clean the mass air flow sensor , you need to get a can of CRC mass air flow cleaener frm auto zone, Kragen, Pepboys, Sensor is attached to the tube (next to airfilter). again you need to use mass air flow cleaner ( CRC ). I use this on my ford windstar and Nissan sentra 05 and 95. it runs better after cleaning the mass air flow sensor.
What might cause and how might you fix the speedometer on your 1992 4Runner which works sporadically and sometimes not at all?
I suspect that you have a bad contact on your speed sensor connector in your transmission. Check connector underneath the car on the driver side, if connector is clean you might need to replace the sensor ( electrical pulse generator ) that's where you plug in the connector...
How do you clean ABS Sensors on Peugeot 307?
To clean the ABS sensors on a Peugeot 307, first ensure the vehicle is securely lifted and supported. Locate the ABS sensor on each wheel hub, disconnect the electrical connector, and carefully remove the sensor. Use a soft cloth or a brush with mild cleaning solution to clean any dirt or debris from the sensor. Reinstall the sensor, reconnect the electrical connector, and ensure everything is secure before lowering the vehicle.
How much 134a freon do you need for a 2002 Nissan frontier 4x4 if added to much how to remove it?
The air conditioning system capacity of the 2002 Nissan Frontier is 25 ounces of R134A type refrigerant. The Clean Air Act of 1990 requires the refrigerant to be removed by a certified technician.
How do you replace a throttle sensor in a 1988 Nissan Sentra?
Is it easy to replace a throttle body in an 88 sentra? How do you clean a throttle body
How do you change a speed sensor on a 95 Ford Aerostar?
Removal: 1. Disconnect the negative battery cable. 2. Detach the speed sensor connector at the rear differential. 3. Remove the sensor hold down bolt, then remove the sensor. 4. Clean the axle mounting surface using care not to get any dirt in the axle housing. 5. Inspect and clean the magnetized sensor pole piece. To install: 6. Lubricate the new o ring on the sensor with new motor oil, then install the sensor. 7. Tighten the retaining bolt to 30 ft. pounds (40Nm). 8. Reattach the wiring harness connector. Connect negative battery cable.
I have a 91 Chevy pickup that runs for 15 min then dies has new coil ignitio module and pickup coil?
I had the same problem bud. Remove and inspect the crankshaft sensor. Also clean the connector pigtail inside with a spray for electronic contacts. Inspect the connector pins of the pigtail closely for damage. Get your sensor at Oreillys NOT autozone.
1989 Nissan 240sx start up revs up high then dies?
When i had this prblem it was my mass air flow sensor check the wiring and clean the sensor its an expensive part if its bad put simple to replace
How do you clean map sensor on 2000 Camry?
To clean the MAP (Manifold Absolute Pressure) sensor on a 2000 Camry, first, disconnect the negative battery terminal and unplug the sensor's electrical connector. Carefully remove the sensor, then use a soft cloth or a brush to gently clean it, avoiding any harsh chemicals. You can use electronic cleaner spray specifically designed for sensors, spraying it on the sensor's diaphragm and allowing it to dry completely before reinstalling. Reattach the sensor and the battery terminal, and start the engine to ensure it's functioning properly.
