0
What else can I help you with?
Does your 1992 miata have rear struts and shocks or just shocks?
The 92' Miata, (also known as a MX-5), has a Strut Assembly in the rear suspension. It consist of a Shock, Coil Spring, and a Strut Mount.
Does a 1990 Dodge Spirit have shocks or struts?
Struts front, shocks rear.
How do you remove and replace rear air shocks on a 2002 Buick La Sabre?
The 2001 Buick LeSabre rear shocks are held in place with a retaining bolt on each end of the shock. Remove the retaining bolts and the old shocks will come off. Reverse the process to install your new rear shocks.
How do you change rear shocks in Mercedes 1989 560sel?
Jack up the car. Unscrew two bolts in the rear bearing arms, then unscrew the top bolts. You will need to take out the back of the rear seat in order to get to these. Then the shocks can be taken out and new installed.
How do you replace rear struts Dodge Intrepid?
The Dodge Intrepid does not have rear struts. This automobile has rear shocks and springs. The shocks can be removed by removing the retaining bolts on the top and bottom of the shock. Reverse the process to install the new shocks.
How do you change rear shocks on 2000 ford exployer?
top bolts seem to be difficult to reach ?
What are Mazda Miata Frankenstein Bolts?
Miata Frankenstein Bolts are hardtop posts available to all Miatas from 1990-2005. They are equipped on Miatas that have removable hardtops. The Frankenstein bolts are mounted on the small chrome pieces near the upper corners of the trunk. The rear of the hardtop has two chrome covers that include bolts and shims that will tighten around the frankentstein bolts to secure the rear of the hardtop to the car. If your Miata does not have them, they can purchased to replaced the two chrome bolts closest to the rear window on the chrome piece. While installing them with a Phillips head screwdriver, Loctite is recommended to ensure the bolts do not back out. While not safe to do so, I have installed a hardtop without the Frankenstein bolts to see what would happen. Running only the front latches attached, I was able to drive around with minimal risk up to 60mph. Above 60mph, the generated air began lifting the rear of the hardtop in the air, creating a 1-2inch gap between the hardtop and the car. Do so at your own risk, but if you want to purchase a hardtop, do not have the means to carry it by truck and do not have Frankenstein bolts, it is relatively safe to mount it to your Miata for transport at low speeds.
Where do you get a right rear strut assembly tower for 1990 Chevy Beretta GT?
There are no rear struts in the Chevy Beretta. Only shocks.
How do you remove the rear inner wheel well on a 1990 miata?
To remove the rear inner wheel well on a 1990 Miata, first, ensure the vehicle is securely lifted and supported. Remove the rear wheel and then detach any screws, bolts, or clips securing the inner wheel well to the body. Carefully pull the inner wheel well away from the vehicle, being cautious of any wiring or components that may be attached. Finally, inspect for any additional fasteners that may need to be removed to fully free the wheel well.
How do you install rear axle for Raptor 660R 2003?
Remove the U-bolts and the shocks. Remove the wheels, shocks, calipers, driveshaft,Êspring bolts andÊbrake lines. Install the rear axle and install everything back. Bolt in the torque arm and the lower control arms. You may want to get the help of somebody in doing this.
How do you replace rear shocks on a catera?
To replace the rear shocks on a Cadillac Catera, start by safely lifting the rear of the vehicle and securing it on jack stands. Remove the rear wheels to access the shocks, then unbolt the lower and upper mounting points of each shock absorber. Once detached, install the new shocks by reversing the removal process, ensuring all bolts are tightened to the manufacturer's specifications. Finally, reattach the wheels and lower the vehicle back to the ground.
How do you change the rear shocks on a 1977 Ford Granada?
Jack up the rear of the car, unless you can put it on a lift, remove shock mount bolts, remove shock, and replace
