answersLogoWhite

0

If the axle is pulling out of the trans, you proably have a failed motor mount. That lets the engine and trans move around to much.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

Difference between Resilient seated valves and Metal seated valve?

The difference is "soft seated" or "metal seated". Soft seated valves are used in gas applications were any leakage is absolutely not tolerated. The materials used are Teflon or ceramic. Metal seated valves can have very tight shut-off, it all depends on the coating, pressure in the line, and the lapping of the surfaces.


How do you change left front turning signal on 91 sonoma?

To change the left front turn signal on a 1991 GMC Sonoma, start by opening the hood and locating the turn signal assembly. Remove the retaining screws or clips securing the assembly, then carefully pull it out. Disconnect the electrical connector and replace the burnt-out bulb with a new one, ensuring it is properly seated. Reassemble the assembly by reconnecting it and securing it back in place.


Is it seated or sited?

seated or sitted


20 hp Briggs broke push rod Put new one in now it doesnt start?

The obvious answers would be that it is not in correctly and seated, or it is not correctly adjusted for 0.004 - 0.006" of clearance.


Why is my tubeless tire losing air overnight?

Your tubeless tire may be losing air overnight due to a puncture, a faulty valve stem, or improper installation. It is important to inspect the tire for any damage and ensure that it is properly seated on the rim to prevent air leakage.


What does seated figure mean?

A person who is seated or sitting.


How do you remove the ignition on a 2000 ford expedition xlt?

Ignition Lock Cylinder Removal & Installation 1. Disconnect the negative battery cable. 2. Detach the key warning chime connector. 3. Turn the key to the RUN position. 4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column. To install: 5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip. 6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer. 7. Turn the key to the OFF position, allowing the retaining pin to properly seat. 8. Install the 2 shroud halves and retaining screws. 9. Connect the negative battery cable. 10. Check for proper starting in PARK and NEUTRAL.


How do you change the ignition on 98 f 150 do you have to remove the column?

Ignition Lock CylinderRemoval & Installation1. Disconnect the negative battery cable.2. Detach the key warning chime connector.3. Turn the key to the RUN position.4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column.To install:5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip.6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer.7. Turn the key to the OFF position, allowing the retaining pin to properly seat.8. Install the 2 shroud halves and retaining screws.9. Connect the negative battery cable.10. Check for proper starting in PARK and NEUTRAL.


How do you unlock ignition key cylinder for 1997 f150?

Ignition Lock CylinderRemoval & Installation1. Disconnect the negative battery cable.2. Detach the key warning chime connector.3. Turn the key to the RUN position.4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column.To install:5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip.6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer.7. Turn the key to the OFF position, allowing the retaining pin to properly seat.8. Install the 2 shroud halves and retaining screws.9. Connect the negative battery cable.10. Check for proper starting in PARK and NEUTRAL.


How do you change the ignition cylinder in a 88 ford f250?

Ignition Lock CylinderRemoval & Installation1. Disconnect the negative battery cable.2. Detach the key warning chime connector.3. Turn the key to the RUN position.4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column.To install:5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip.6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer.7. Turn the key to the OFF position, allowing the retaining pin to properly seat.8. Install the 2 shroud halves and retaining screws.9. Connect the negative battery cable.10. Check for proper starting in PARK and NEUTRAL.


Do you have to remove the steering column on a 98 f150 to change ignition?

Ignition Lock CylinderRemoval & Installation1. Disconnect the negative battery cable.2. Detach the key warning chime connector.3. Turn the key to the RUN position.4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column.To install:5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip.6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer.7. Turn the key to the OFF position, allowing the retaining pin to properly seat.8. Install the 2 shroud halves and retaining screws.9. Connect the negative battery cable.10. Check for proper starting in PARK and NEUTRAL.


How do you change a headlight on a 1972 Datsun 240Z?

To change the headlight on a 1972 Datsun 240Z, first, open the hood and locate the headlight assembly. Disconnect the electrical connector and remove the retaining ring or screws holding the headlight in place. Carefully take out the old headlight and replace it with a new one, ensuring it is properly seated. Finally, reattach the retaining ring, reconnect the electrical connector, and test the headlight.