0
To remove the subframe from a Honda Odyssey, first ensure the vehicle is safely lifted and supported on jack stands. Disconnect the battery, then remove any components obstructing access to the subframe, such as the exhaust system and suspension parts. Next, unbolt the subframe from the chassis, typically involving several bolts around the perimeter and possibly a few in the center. Finally, carefully lower the subframe from the vehicle, ensuring to handle it safely and avoid damaging any attached components.
What else can I help you with?
How do you remove the engine?
how do you remove the engine? Is it pulled from the top or do you unbolt the sub frame and slide it out from under the car?
How do you replace the subwoofer on a 2004 Honda Pilot?
how to remove the right rear panel for sub woofer remove
Will a gsxr k1 rear subframe fit a hayabusa?
It won't just bolt on , your gona have to remove the Busa sub frame 1st, then get the angle of the Gìxer sub frame how you want it. Mark the sub frame. Were it needs to be cut , find a good Aluminum welder and have them weld the ends for
Does the sub frame for a left hand drive 2003 Honda Accord the same as the right hand drive?
Yes, they are identical.
Do you have to remove engine from the bottom of a Oldsmobile sillhouette?
Yes. You remove both engine and transaxle with the sub-frame at the same time out the bottom.
Is the 67 nova a full frame car or sub frame?
It's a sub frame car.
How do you change rack and pinion on a Honda Odyssey?
Set the wheels and steering straight. Remove pressure line and return line from the rack side. unbolt and pop out the steering shaft. Must do so from driver panel. There are 5 bolts all in all that keep the rack attached to frame, unbolt them. There's a rear engine mount that sits over the rack, unbolt that. You'll need to lower the sub-frame from driver side by a good six inches. That will consume a lot of time. You'll be raising engine and lower sub-frame from driver side to create enough space to pull the rack out and replace it. With certain bolts hard to access and figuring out that i needed to drop the sub-frame, the job took appx six hours. Way more than i had in mind.
Where is the location of transmission temperature sensor on Honda 2002 odyssey van - is it difficult to change?
It's located on the bottom of the transmission behind the front transmission mount. Replacement is moderately difficult. It requires disconnecting the transmission from the sub-frame, lifting the transmission a little, then removing the front mount. It's best done with the van on a hoist.
How do you change the front sub-frame bushes on a Nissan Note?
To change the front sub-frame bushes on a Nissan Note, first, securely raise and support the vehicle on jack stands. Remove the front wheels for better access, then unbolt the sub-frame from the chassis. Use a suitable tool to press out the old bushes and install the new ones, ensuring they are properly seated. Finally, reassemble the sub-frame, torque the bolts to the manufacturer specifications, and reinstall the wheels before lowering the vehicle.
How do you remove an oil pan on 96 grand am 6cyl with out pulling engine?
drop the sub-frame, sorry bud one or the other!
How do you change a stabilizer bar on a 2000 Malibu?
1 Remove wheel, tie rod ends, nuts from link bolts. 2 Remove stabilizer bar bushings 3. unbolt rear engine mount bracket from sub-frame 4 remove sub-frame (6) bolts 5 Drop sub-frame 3 inches onto jack stands. 6 remove stabilizer bar and bushings through wheel well. 7. have 1 beer only install new stabilizer in reverse order IMPORTANT to observe factory torque specifications
How do you change stabilizer bar on a grand prix 2004?
I have a 2000 that i have to replace and my book says you can buy the book taht will tell you how to do it from Auto Zone for $20 dollars. Put the car up on jack stands, remove both front tires, remove the 4 bolts from the pinch point, there are two on each side, remove the 2 bolt for the rear sub-frame , put a jack under the sub-frame before you remove those bolts, once you have those bolts remove lower the rear sub-frame remove the two bolt from the end of the sway bar 1 bolt on each side on each side. then remove the sway bar, pull it back and tip it down and pull out one side of the wheel well.
