answersLogoWhite

0

First you need to take the handles and door panel off. Then you need to see whether the window has jumped off the track or if the track has come apart or is broken. If it has jumped the track, put some silicone caulk in the track and set the window back in. Make sure the track is in the down position. After replacing the window in the track, roll it all the way up and leve it for a few hours. If the track has broken, you will neew to find out where it is broken and fix or replace it. There could be a broken weld which a GOOD welder can fix for you. If you're not a professional welder do NOT try to do it yourself. It is a precision fit.

User Avatar

Wiki User

19y ago

What else can I help you with?

Related Questions

HOW Do you set a power window back on track on a ford focus?

To set the power window back on track in a Ford Focus, you have to remove the door panel. Once you get in there, you will see the track that you will need to put the window back on.


How do you put a power window of a Chevy blazer back on track?

You will need to remove the inside door panel of your Chevrolet Blazer. Remove the window retaining clips. Put the window back into the window track. Tighten the window retaining clips.


How do you place the passenger window back in track on a 1999 Intrepid with power windows?

Remove the inside door panel of your 1999 Chrysler Intrepid. Remove the window retaining clips. Put the window back into the window track. Secure the window with the window retaining clips.


How do you manually raise power window?

I had to to take the door panel off remove the window motor raise the window then put the motor back on


How do you repair a drivers side power window of a 2001 dodge caravan which has fallen into the door?

Remove the inside door panel. The entire power window mechanism will be visible. Put the window back onto the window track.


How do you replace 1995 Toyota Celica power window regulator?

remove back seat, remove screws bottom and top of panel, remove panel. remove 3 bolts and motor arm, window and regulator will pull out.


How do you get the back power window to go back up when the motor quits working?

REmove the door panel and clip the cables on the regulator.Here's how to remove a door panelhttp://www.ricksfreeautorepairadvice.com/uncategorized/remove-a-door-trim-panel-from-any-vehicle%E2%80%94-without-a-diagramHere's how to replace the regulator and clip the cablehttp://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator


Remove and replace power window motor 92 chev caprice?

cannot get motor to line back up. when I do it jams


Replacing a back window on a Monte Carlo?

How do I remove the back window in a 1998 Monte Carlo? how do I replace this?How do I remove from other Car's model


How do you install a window power lift motor on a 1993 Jeep Grand Cherokee?

i am going to be doing this this weekend....this is how my chilton says to do it lower window to down position(if you can) remove door panel remove window weatherstripping remove black window surrond(should be a screw on top of surrond towards back edge) then stationary window should unbolt then remove pins that hold operator to track pick up and pull out the operating window


How does one access window lock switch on 1997 Jeep Cherokee?

I'm not sure if this will help but heres what I have on power windows. lower window to down position(if you can) remove door panel remove window weatherstripping remove black window surrond(should be a screw on top of surrond towards back edge) then stationary window should unbolt then remove pins that hold operator to track pick up and pull out the operating window


How do you repair power window on a 1997 Z24?

You must first take off the door panel, by removing all door panel screws. Then you have to remove the two lower bolts that hold the window in and remove the window. Then you must drill out the rivets that are holding the power window motor in place, unplug it and remove it through one of the holes in the door ( remove the plastic covering) For re installation it is a bit tricky, have to transfer a couple parts onto the new unit with screws or rivets, and putting the window motor in, you need big rivets or possibly short bolts but they are hard to get in. Then plug it back in and put the window back in, and do up the two bolts that hold the window on. Good luck.