answersLogoWhite

0

there are two clips along with bottom part of the back seat....pull it out and release it.

and then you will find there are two screw on both sides next to the seat belt clip.

unscrew them and push the seat up.....job done!!

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you change a back motor mount on a 2002 Mitsubishi mirage decoupe?

how to change a back motor mount on a 2002 Mitsubishi mirage decoupe


Is it true that you can access the fuel pump on 98 Mitsubishi mirage under the back seat?

Possibly, remove the back seat and see for yourself.


What size are the back speakers in a Mitsubishi mirage?

6X9


Where is the reverse light switch on a 2000 Mitsubishi mirage?

The Back up light switch (reverse light switch) is located on the top of the transmission. If you remove the air cleaner element, look down, a little to the left you will be able to see it.


Where is the gear valve for a Mitsubishi mirage?

On the intake manifold, back dirver side.


How do change pulley belt 2000 Mitsubishi mirage?

To change the pulley belt on a 2000 Mitsubishi Mirage, first ensure the engine is off and cool. Disconnect the negative battery terminal, then locate the tensioner pulley and use a wrench to relieve tension on the belt. Remove the old belt from the pulleys, route the new belt according to the diagram usually found on a sticker under the hood, and then adjust the tensioner back into place. Finally, reconnect the battery and start the engine to check the belt operation.


HOW DO I REMOVE THE WIPER ARM FROM A 2014 MITSUBISHI MIRAGE?

To remove the wiper arm from a 2014 Mitsubishi Mirage, first, lift the wiper arm away from the windshield. Look for a small tab or nut at the base of the arm and either pull the tab or use a socket wrench to remove the nut. Once the fastener is removed, gently rock the wiper arm back and forth while pulling it upwards to detach it from the spindle. Be careful not to damage the spindle during removal.


How do you replace 95 Mitsubishi mirage wheel studs?

To replace the wheel studs on a 1995 Mitsubishi Mirage, first, safely lift the vehicle and remove the wheel. Then, remove the brake caliper and rotor to access the hub. Use a press or hammer to push out the old studs, and then insert the new studs from the back of the hub, ensuring they are seated properly. Finally, reassemble the rotor and caliper, and reinstall the wheel before lowering the vehicle.


How do you replace the ac filter located on a 1998 Mitsubishi mirage?

To replace the AC filter in a 1998 Mitsubishi Mirage, first, locate the filter, which is typically found behind the glove compartment. Remove the screws or clips securing the glove compartment and lower it to access the filter housing. Remove the old filter by sliding it out, and then insert the new filter, ensuring it is oriented correctly. Finally, reassemble the glove compartment by securing it back in place.


How do you replace the headlights on a 96 Mitsubishi Mirage?

Open the hood. Remove the plug on the back side of the light bulbs. Remove the trim ring holding the bulb in. Slide the bulb out of the back side of the housing. Insert new bulb, dont touch the glass. Replace the trim ring. Connect the wire harness plug. Turn on the light switch and check that they are working.


Where is the horn on a 1997 Mitsubishi Mirage LS 2 door?

well i have a 4 dr but it should be the same place and its in the right side back of the engine bay.


How do you replace the thermostat in a 93 Mitsubishi mirage ls . and where is it located?

Very simple, follow the top radiator hose to where it ends, there will be a silver thermostat housing there with 2 bolts. Remove the 2 bolts and replace the thermostat. Make sure you put it back in the same way it was taken out.