0
remove wheel
remove big nut holding axle 32 mm socket
remove two big bolts on top of spindle
Take puncher about 4 mm in diameter and punch out pin holding inner cv joint at transmission .
Pull out everything .
Reverse procedure , but with new axle make sure you will align all marks right /
What else can I help you with?
Will a bad front axle on a 1992 subaru loyale make it shimmy when you accerate?
Yes, it will and generally it is the inboard cv joint.
How do you replace the front wheel bearings on a 1994 Saturn and what is the best way to remove it from the controller arm?
Remove u-joint clip (CV Joint), remove as an assembly, press bearing out.
How do you remove front CV joint on Kubota rtv 900?
is there something holding front axel in trans case
How to Remove of lower front ball joint on 01 jaguar xj8?
To remove the lower front ball joint on a 2001 Jaguar XJ8, first, safely lift and secure the vehicle, then remove the wheel. Next, detach the lower control arm from the ball joint by removing the bolts securing it. Use a ball joint separator tool or a pickle fork to separate the ball joint from the steering knuckle. Finally, remove the retaining nut and pull the ball joint from the control arm, ensuring to replace it with a new one if needed.
Does Toyota make Subaru?
No. Subaru makes Subaru. The two companies did do a joint project. Toyota makes Lexus and scion.
How do you change a front drivers side u joint on a 1993 ford explorer?
How do u remove front axle u joints
How do you change the front universal joint on a 1997 Yamaha Kodiak ATV?
To change the front universal joint on a 1997 Yamaha Kodiak ATV, first, remove the front differential cover and drain the fluid. Next, disconnect the driveshaft from the differential and remove any retaining clips or bolts securing the universal joint. Use a press or a specialized tool to remove the old joint and install the new one, ensuring proper alignment. Finally, reassemble the driveshaft and differential, refill the fluid, and check for proper operation.
How do you take apart a cv joint on a 1990 big bear ATV?
On the cv joint attached to the front differential, if you take off the boot, in front of the bearing, there is a cir clip. If you remove the cir clip the whole cv joint slides out of the differential. Have fun...
How do you replace the ball joints on 1997 E-350 Van?
From: http://en.allexperts.com/q/Ford-780/Ball-Joint-Replacement.htm Ball Joint Replacement [Ford Van] Remove the brake disc. Remove the wheel speed sensor. For additional information, refer to Section 206-09. Remove and discard the cotter pin and nut. Disconnect the tie-rod end. Remove and discard the cotter pin and the nut. Remove the pinch bolt adjuster. CAUTION: To prevent damage to the ball joint seal and the ball joint socket, do not use a pickle fork-type remover to loosen the ball joints. Remove the front wheel spindle. Strike the lower end of the front axle to loosen the ball joint. Remove the front wheel spindle. To install, reverse the removal procedure. Check and, if necessary, align the front end. Remove the wheel spindle assembly. For additional information, refer to Wheel Spindle - E150-E450 in this section. Position the front wheel spindle in a vise, and remove the snap ring from the lower ball joint. CAUTION: To avoid damage to the components, do not use heat to aid ball joint removal. Using the special tool and suitable receiver cup, remove the lower ball joint from the front wheel spindle. Using the special tool and suitable receiver cup, remove the upper ball joint. Installation CAUTION: To avoid damage to components, do not use heat to aid installation. NOTE: Clean the wheel knuckle ball joint bores. NOTE: The lower ball joint must be installed first. Using the special tool with suitable receiver cups, install the lower ball joint. Using the special tool with suitable receiver cups, install the upper ball joint. Install the snap ring in the groove at the bottom of the ball joint. Install the front wheel spindle.
How do you remove the front drivers side cv joint from a 1997 Olds bravada?
unscrew it unscrew it unscrew it unscrew it
How do you replace a front right ball joint on a 1997 Ford F-150?
To replace the front right ball joint on a 1997 Ford F-150, first, safely lift and support the vehicle, then remove the front wheel. Next, disconnect the brake caliper and rotor, then remove the lower control arm by unbolting it from the frame and the steering knuckle. Use a ball joint separator to remove the old ball joint and press in the new one, then reassemble everything in the reverse order. Finally, ensure all bolts are torqued to specifications and perform a wheel alignment.
What would cause a 2002 Subaru Forester to periodically make a loud clunking noise around the right front tire?
I had periodic clunking in the front tire of a 94 legacy. I Needed the "Ball joint" replaced. Parts and labor cost a couple hundred bucks. Get it fixed b/c if it snaps youll crash. It typically clicked or clunked as I made turns slowly like out the drive way or into a parking lot.
