0
They just screw into the exhaust pipe. There are clips that keep the electrical connectors in place, you will have to pry those out, but it should not be a problem. Then all you do is screw the new one back in, and press the clip back into the hole for the elec. connection
Well, i am in the process of changing the sensor as we speak...and i am dirty and hot (yuma, september, over 100 degrees Fahrenheit, shoot me).
I bought my new sensor from Autozone where they were about 50-55 dollars. A sensor connected to a cable with 4 loose wires and a few more parts which would complete the plug (which you build yourself).
My cables from my sensor lead up to a connector which had a perfect fitting plug on it...which was different that the new one though...so replacement in unavoidable.
I just can't get to the rest of the plug to fit the new connectors on. there is some sort of cover (metal, sharp edges) covering the cables. So, i am now off to remove such plate and get to the cable to place new connectors...
Don't do it yourself but pay a mechanic 40 bucks...that's what it's worth.
First guy was right, they just screw in and out. Go back to autozone or checkerauto and you can rent an "oxygen sensor" wrench/ratchet kit. (once you return the kit autozone will refund all your rent money). The kit comes with a dozen different sized and shaped sockets that will fit over your oxygen sensor to help pull them out easy. (my oxygen sensors were covered with dirt that I had to scrape off first, because I go off roading a lot). Make sure you buy the oxygen sensors that already come with the attachment clip for the wires (this will save you lots of time and frustrations) they're only a few dollars more. Before you screw the new oxygen sensor back into place, you should probably put some RTV sealant around the washer. You can get that at autozone too. It comes in a tube for a few dollars. Make sure you get the RTV sealant marked "sensor safe" or "wont harm oxygen sensors" and also that it has a high heat tolerance.
What else can I help you with?
How many oxygen sensors does an Isuzu Rodeo have?
The Isuzu Rodeo can have 3 or more oxygen sensors. The oxygen sensor delivers information to the powertrain module.
How many oxygen sensors on in a 2003 Isuzu rodeo?
The 4 cylinder models have two oxygen sensors, and the V6 models have four oxygen sensors.
Where are the oxygen sensors on 1997 Isuzu Rodeo?
it depends on the model of engine, my 97 rodeo with the 4ze1 motor has the map sensor for air intake but doesnt have an O2 sensor for the exhaust.
How many oxygen sensors are there on a 1999 Dodge Ram van 1500 Also can they just be cleaned or is it best to replace them?
Two sensors, and replace them.
How do you replace the oxygen sensors on a 96 mustang gt?
The oxygen sensors that connect to the exhaust system. There should be two, and they should screw into the side of the exhaust.
Where are the oxygen sensors and how do you replace them on a 1998 Lincoln continetal?
the auto parts dealer said that it was 4 oxygen sensors on that car.the 1998 Lincoln continetal
Do you have to replace all 4 oxygen sensors at one time?
No.No.
How do you replace the oxygen sensors on a 1999 Volvo s80?
To replace the oxygen sensors on a 1999 Volvo S80, first, ensure the vehicle is cool and safely elevated. Locate the oxygen sensors, which are typically found on the exhaust manifold and downstream in the exhaust system. Disconnect the electrical connectors and use a specialized oxygen sensor socket to unscrew and remove the old sensors. Install the new sensors by threading them in, tightening them securely, and reconnecting the electrical connectors.
How do you replace Mitsubishi 3000gt oxygen sensors?
To replace the oxygen sensors on a Mitsubishi 3000GT, first, ensure the vehicle is off and cool. Locate the oxygen sensors, which are usually found on the exhaust manifold and after the catalytic converter. Disconnect the electrical connectors and remove the sensors using an O2 sensor socket or a wrench. Install the new sensors by threading them into place, reconnecting the electrical connectors, and ensuring they are secure.
Where are the oxygen sensors and how do you replace them on a 1999 Pontiac Montana?
In exhaust pipe before catalytic converter unscrew to replace
Replace water pump on a 1994 Isuzu Rodeo?
replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo 6 cylinder
What should you expect to pay to replace the oxygen bags on a 2005 Chev Impala?
Oxygen bags? Are we talking air bags or oxygen sensors?
