0
"you push the Trip Odometer button until the total miles (not trip miles) is displayed. Then turn off the car and hold the Odometer/Trip Odometer select button donw while you push the Power Button twice to get to Ignition On and continue holding the Odometer/Trip Odometer for five additional seconds."
In the case of our 2010 RAV4, a mobile mechanic in orange county, ca was reseting for me today the odometer had to be in the "trip A" not the ODO vehicle miles displayed,
tried it three times with the ODO displaying total miles and it would not reset, then did the same procedure but had the ODO in trip "A" and it worked first time perfectly.
You will know it worked because the "maint" light will flash and then go out, shut off the ignition and start the car to confirm it has reset (the "maint" light will go out after starting the car).
What else can I help you with?
Reset the maintenance required light on 08 Toyota rav 4?
maintenance with engine
How do you reset the maintenance required light on a 2007 Toyota Tacoma V6?
disconnect the battery
How do you reset the maintenance reqired light in the 2011 smart key Toyota RAV4?
How do you reset the maintenance required light in the 2011Toyota RAV4 with a smart key starting system
How do you Reset Maintenance Warning Light on a 2008 Toyota 4Runner?
How to Reset Maintenance Warning Light on a 2008 Toyota 4Runner
How do you reset the maintenance required light in a 2007 Toyota?
To reset the maintenance required light in a 2007 Toyota, first, turn the ignition switch to the "OFF" position. Then, press and hold the trip meter reset button while turning the ignition to the "ON" position (do not start the engine). Continue holding the button until the maintenance light flashes and then turns off. Release the button, and the light should be reset.
How do you reset the 'maintenance required' light on an '12 Toyota Rav 4?
To reset the 'maintenance required' light on a 2012 Toyota RAV4, start by turning the ignition key to the "ON" position without starting the engine. Press the gas pedal slowly three times within five seconds. Then, turn off the ignition. When you start the car again, the maintenance light should be reset.
How do you reset the maintenance required light on a 2010 Toyota Tacoma?
To reset the maintenance required light on a 2010 Toyota Tacoma, start by turning the ignition to the "ON" position without starting the engine. Press the gas pedal three times within five seconds. Turn the ignition off, then start the engine to ensure the light is reset. If the light remains on, repeat the steps.
How do you reset maintenance required light on 2015 Toyota RAV4?
To reset the maintenance required light on a 2015 Toyota RAV4, first turn the ignition to the "ON" position without starting the engine. Then, press the gas pedal three times within five seconds. Finally, turn off the ignition and start the engine to ensure the light has been reset.
How do you reset a 2010 Toyota matrix maintenance required light?
To reset the maintenance required light on a 2010 Toyota Matrix, turn the ignition to the "ON" position without starting the engine. Press the gas pedal three times within five seconds. Then, turn the ignition off and back on again, and the light should be reset. If the light remains on, repeat the process to ensure it was done correctly.
How do you reset the maintenance required light on a 2011 Toyota RAV4?
You will need to take it into a mechanic. They will be able to check out your vehicle and then they can turn off the light.
Toyota rave 4 You changed oil how do you get the oil maintenance light required now to go out?
Your drivers manual should give you the information to reset the oil maintenance light.
How do you reset the 'maintenance required' light on an 2007 Toyota Rav 4?
To reset the 'maintenance required' light on a 2007 Toyota RAV4, start by turning the ignition to the "ON" position without starting the engine. Press the gas pedal three times within five seconds. After doing this, turn the ignition off and then start the engine again; the light should be reset. If the light remains on, repeat the process to ensure it has been properly reset.
