0
If you're checking the rear struts there's nothing under the seat; there are 3 bolts under the headrests but everything else is under the car. And FYI- it's a nightmare getting the struts off the rear of this car. I had to take mine to a mechanic cause it basically involves unbolting the entire rear end to get the struts off the vehicle.
What else can I help you with?
Diagram of removing rear seat of 1990 Nissan Stanza?
To remove the rear seat of a 1990 Nissan Stanza, start by locating the seat bottom clips or bolts at the front edge of the seat base. Use a flathead screwdriver or wrench to release these fasteners. Next, lift the seat bottom upwards to detach it from the rear brackets. Finally, for the seat back, locate any bolts or clips securing it to the body and remove them before lifting the seat back out.
Where is the oil drain plug located on 1991 Nissan Stanza?
On a 1991 Nissan Stanza, the oil drain plug is located at the bottom of the engine oil pan. To access it, you'll need to look underneath the vehicle, typically near the center or toward the back of the oil pan. The drain plug is usually a hex or bolt-type fitting that can be removed to drain the engine oil. Always ensure the vehicle is securely lifted and supported before attempting to access the drain plug.
Where is the thermostat housing located at on a Nissan Stanza?
towards the bottom of the motor follow the bottom radiator hose to the engine block and you should see four bolts for the thermostat housing
Where is the thermostat located on a 1992 Nissan Stanza?
Follow the bottom hose of the radiator to the block. Where the hose enters is the location. Changing this has been answered.
How do you remove back seat of Nissan Stanza 1991 to change the fuel pump?
To remove the back seat of a 1991 Nissan Stanza, start by locating the release mechanism, which is usually found at the front edge of the seat bottom or at the base of the seat back. Pull up on the seat bottom to detach it, then check for any bolts or clips securing the seat back and remove them. Once the seat back is free, lift it out of the vehicle to access the fuel pump. Make sure to disconnect the battery before working on the fuel system for safety.
Do you have to access the starter of a 98 Nissan maxima for the bottom of the car?
yes yes
Center console Nissan Altima?
The Nissan Ultima center console can be removed by removing the retaining bolts. There are four retaining bolts on the bottom of the console.
Where is blower resistor located on a 93 Nissan altima?
The blower motor resistor on a 1993 Nissan Altima is behind the glove compartment on the passenger side of the vehicle. To access the blower motor resistor, the glove compartment can be removed by lowering the bottom as much as possible and removing it from the hinges.
How do you completely access the transmission filter with removal of the transmission pan on a 2003 Nissan altima?
The screen is accessable by removing the bottom pan of the transmission. most people clean it with carb cleaner or brake cleaner and dry it before reinstalling it.
Where is the fuel filter located on a 1992 Nissan Stanza?
the fuel filter is located on firewall on drivers side......has 2 fuel lines going to it one on bottom and one out of the top
How do you replace the bottom radiator support on a 1991 Nissan Maxima?
To replace the bottom radiator support on a 1991 Nissan Maxima, start by disconnecting the battery and removing any components obstructing access, such as the radiator and front bumper. Next, unbolt the old radiator support from the chassis and carefully remove it. Install the new support by aligning it with the mounting points and securing it with bolts. Finally, reassemble the components you removed and reconnect the battery.
How do you replace the alternator on a 1989 Nissan 240SX?
Drive the car up onto ramps or jack the car up to change the alternator you need have access from the bottom of the engine. Access to the alternator is very tight. First disconnect the battery. Accessing from the top loosen the drive belt and remove the adjusting bolt, ground wire, battery wire and plug in connector from alternator, do this before removing the bottom bolt from alternator. Once bottom bolt is removed the alternator is to be taken out the bottom, it is a tight but it will come out. Hope this helps.
