0
What else can I help you with?
Why does your 06 Isuzu Ascender engine whine?
I replaced the engine idler pulley that I bought from Autozone for about $17 and eliminated the noise. I initially thought the bearings on my alternator were going out but when I replaced the pulley all the whining noise disappeared. Good Luck!
How do you change the serpentine belt idler pulley ona 2006 Isuzu ascender?
Requires two person team. Step One: Look at serpentine belt diagram on front of engine. Arrow points to idler tension pulley. (Front Left side of engine) Loosen this 15mm bolt. Step Two: Loosen Idler pulley bolt - 15mm. Step Three: One person push down on idler tension pulley with tire removal tool or cheater bar on front left of engine while second person lifts belt off alternator. Step Four: Remove Idler pulley and replace with new one. Tighten bolt to idler pulley Step Five: One person push down on idler tension pulley with while the other fits belt on alternator and around idler pulley. Step Six: Make sure belt fits as noted on belt diagram and Tighten bolt on idler tension pulley (front left side of engine). Approximate time: 10 minutes
What is the pulley under the alternator in a 1994 Chevy caprice 5.7L and how hard is it to change?
Are you talking about the "idler pulley"? They are quite simple to change. Loosen the serpentine belt by using a socket on the center of the tensioner pulley, slide the belt off the idler pulley, use a socket to pull the center bolt of the idler pulley and replace the pulley with a new one.
How do you change the idler pulley on 1994 Cadillac eldorado?
Take the belt off, un-bolt the idler pulley, bolt the new pulley on, and finally put the belt back on and Viola!!
How do you change a idler pulley on a Chevy Colorado?
To change the idler pulley on a Chevy Colorado, first, disconnect the negative battery terminal and relieve any tension on the serpentine belt using a wrench on the tensioner pulley. Remove the belt from the idler pulley, then unbolt the idler pulley from its mounting bracket using the appropriate socket size. Replace it with the new pulley, reattach the belt, and finally reconnect the battery terminal. Make sure everything is secure and test the installation by starting the engine to ensure the pulley operates smoothly.
How do you change the idler pulley on a 43 vortec?
Take the belt off, take the bolt off of the idler pulley, take the pulley off, put a new one on replace the bolt, and put the belt back on
Where is the idler pulley on a 1996 Chevy Cavalier?
I don't believe there is an idler pulley on that model, just a tensioner pulley
How do you replace an idler pulley on a 97 Buick park ave ultra?
go to youtube and type in ericthecarguy and change pulley
How do you change a idler pulley on a 2003 Malibu?
First you would need to take the serpentine belt off of the engine, and then remove the bolt in the center of the idler pulley. I have included an instructional vieo of how this is done.
How do you change the idler pulley on a 1994 Ford Bronco?
To change the idler pulley on a 1994 Ford Bronco, first, ensure the engine is off and cool, then disconnect the negative battery cable. Use a socket wrench to relieve tension on the serpentine belt by rotating the tensioner pulley, and remove the belt from the idler pulley. Unbolt the old idler pulley using the appropriate socket size, then install the new pulley and reattach the serpentine belt following the routing diagram. Finally, reconnect the battery cable and start the engine to ensure everything is functioning properly.
Can the idler pulley be the problem on my car because when i brake the car dies?
The idler pulley has nothing to do with the brakes. If the idler pulley is bad it could throw or break a belt, and then your engine will stop.
How do you change an idler pulley on a 1995 Cadillac Seville sls?
To change the idler pulley on a 1995 Cadillac Seville SLS, first, disconnect the negative battery cable to ensure safety. Remove the serpentine belt by using a wrench to relieve tension on the tensioner pulley. Next, unbolt the idler pulley from its mount using the appropriate socket, and replace it with the new pulley. Finally, reattach the serpentine belt, ensuring proper routing, and reconnect the battery cable.
