0
The tools you will need:
A #2 Phillips head screwdriver, A Standard head screwdriver, A 10mm Socket and ratchet.
First take out all of the screws in the door panel. There is one in the handle that opens the door, and 2 in the door panel handle. Use the flat screwdriver to pop off the covers. Taking out the door handle is a little tricky. Slide it towards the front of the car and pull out. You might not get it the first try. Once you get the handle out enough, you will be able to see 2 metal rods connecting to it(towards the back of the car). Using the standard screwdriver, pull the plastic piece(either blue or red) towards you and it should unclip from the rod. Next, pick up on the rods and they should come out of the handle. Once all screws and the door handle are removed, you can take off the panel.
To remove the door panel, simply pull it off, starting at the bottom of the door and prying your fingers between the panel and the door. You will hear a series of pops. You didn't break anything. If it doesn't come fairly easy, don't pull too hard. You may have missed a screw. Once the panel swings freely on the window slot, get it close to the door and pick up, as the top rests in the window slot. If you have power windows, you will have to unclip the wires going to the switch.
Once the panel is off, drop the window and remove the 2 Phillips screws holding the window on the track. After the window is off, tape it up so it is out of your way. Next, take the socket and remove the 3 nuts holding the window motor, (towards the front of the car, in the middle), and then the three(maybe four) that hold the metal track in place. Once those are off, good luck getting out the hole in the bottom of the door. It will not free fall in the door as the stud screws are attached to the motor and regulator. You will also have to disconnect the motor wire. Once it is out of the door, there are 3 screws or bolts that hold the motor to the regulator. take those out and the motor should slide off easily. Then do it in reverse to put it back together.
What else can I help you with?
Will a window regulator for a 2000 Hyundai elantra work with a 2000 Hyundai Accent?
no, different designs.
How would i Break into Hyundai Accent?
break the window :)
How do you replace a driver door window in a Hyundai Elantra?
To replace the driver door window in a Hyundai Elantra, first, remove the interior door panel by unscrewing any visible screws and gently prying off clips. Once the panel is off, disconnect the window regulator and any wiring connected to the window motor. Carefully remove the broken glass and install the new window by guiding it into the regulator tracks, then reconnect the regulator and wiring. Finally, reattach the door panel and test the window operation.
How to install grand am regulator?
Which regulator and what year? You have a window regulator, voltage regulator, fuel pressure regulator to name a few.
How do you remove a right rear window regulator from a 2007 Hyundai Sonata?
magic
How do you install a new window regulator on a mgzr drivers door?
To install a new window regulator on a MGRZ driver's door, remove the door panel and the wiring attached to the power window mechanism. Remove stereo speaker from the inside door and the window glass. Remove the old window regulator and replace with new.
How do you install a new window regulator on a drivers door of Pontiac Montana?
turn bolts to the left, install regulator, turn bolts to the right
How do you remove window crank handle in 1999 Hyundai accent?
With a hammer and pry bar.
Will a window regulator from a 1996 Hyundai Elantra work in a 2000 Elantra?
Its should be same thing
How do you fix passenger window in 96 Hyundai accent?
Identify the fault/problem. Repair or replace
How do you replace a 2001 Ford Focus window regulator?
To replace a 2001 Ford Focus window regulator, first, remove the door panel by unscrewing and unclipping it to access the regulator. Disconnect the window from the regulator, then unbolt the old regulator from the door. Install the new regulator in reverse order, reconnect the window, and reassemble the door panel. Finally, test the window operation before securing everything in place.
How do you replace window motor 1996 Chevy Astro?
1. Remove the power window regulator2. Install a pan head sheet metal tapping screw through the sector gear and the backing plate at the hole provided to lock the sector gear into position. Then drill out the motor to regulator attaching rivets.3. Remove the motor from the regulator.To install:1. Lubricate the motor drive gear and the regulator sector teeth. Install the motor to the regulator and check the mesh of the motor to the regulator.2. Install rivets to the motor and the regulator.3. Remove the sheet metal tapping screw.4. Install the power window regulator.
