0
CAUTION: Some models are equipped with anti-theft-radio make sure you have the activation code before disconnecting battery * Disconnect the negative battery cable * Remove the steering column covers and the lower instrument panel cover * To remove the electrical portions of the ignition switch follow the harness back and disconnect the electrical connector then remove the screw and detach the switch from the lock cylinder housing and lower the steering column * The switch/lock cylinder housing is clamped to the steering column by shearhead bolts.Use a chisel and a hammer to tap the bolts in a counterclockwise direction to unscrew them * Remove the lock cylinder/ignition switch assembly from the steering column * Mount the new lock cylinder assembly on the steering column and install new shearhead bolts.Tighten the shear head bolts securley but dont break the heads off at this time * Insert the key and check the lock cylinder and steering column lock for proper operation.When you're satisfied the lock cylinder and steering column lock is operating properly tighten the shearhead bolts until the heads break off. * The remainder of installation is the reverse of removal
What else can I help you with?
How do you install a ignition switch on a Hyundai Elantra?
To install an ignition switch on a Hyundai Elantra, first disconnect the negative battery terminal to ensure safety. Remove the steering column covers by unscrewing the screws, then disconnect the wiring harness from the old ignition switch. Install the new ignition switch by aligning it correctly and securing it in place, then reconnect the wiring harness. Finally, reassemble the steering column covers and reconnect the battery terminal.
How do you remove and install the ignition switch on a 2008 Hyundai sonata?
To remove the ignition switch on a 2008 Hyundai Sonata, first, disconnect the negative battery cable. Then, remove the steering column covers and the ignition lock cylinder by turning it to the "Run" position and pushing the release pin. After that, you can unscrew and detach the ignition switch from its mounting. To install, reverse the process, ensuring the new switch is properly aligned before securing it in place.
How do you remove passenger airbag for 2000 Hyundai Elantra?
remove the complete dashboard and then replace it
How do you remove the hubcaps on a 2001 Hyundai Elantra?
you will have to remove all the lug nuts. just like when you remove the tire!!
How do to change a battery on a Hyundai Elantra?
So the right answer is to locate the battery, remove anything in your way (engine Cover, air filter box, etc.) remove the negative the positive then the hold down. To install reverse the procedure.
How do you install a speedometer cable for a 2000 hyundai elantra?
To install a speedometer cable on a 2000 Hyundai Elantra, first, ensure the vehicle is securely lifted and supported. Remove the instrument cluster by unscrewing it and disconnecting the wiring harness. Locate the speedometer cable at the back of the cluster, disconnect it, and then install the new cable by inserting it into the speedometer and securing it. Finally, reconnect the wiring harness, reinstall the instrument cluster, and test the speedometer for proper function.
How do you remove the backseat in a 1998 Hyundai Elantra?
pull it up on the front edges on either side
How do you go about changing the rear wiper motor on a Hyundai Elantra wagon?
Remove the inside panel from your Hyundai rear door. The wiper motor mechanism will be visible. Remove the wiper motor linkage. Remove the wiper motor wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new rear wiper motor.
How do you remove the clutch pedal switch on a 2003 Hyundai elantra?
To remove the clutch pedal switch on a 2003 Hyundai Elantra, first, ensure the vehicle is in gear and the ignition is off for safety. Locate the switch mounted on the clutch pedal assembly, typically near the top of the pedal. Disconnect the electrical connector by pressing the tab and pulling it off, then remove the switch by unscrewing it or twisting it counterclockwise, depending on the design. Finally, replace it with a new switch by reversing the steps.
Can you take the catalytic converter out of an 05 Hyundai elantra?
No, it is illegal to remove a converter and carries a hefty fine.
How do you install a ball joint in Hyundai Elantra?
To install a ball joint in a Hyundai Elantra, first lift the vehicle and remove the wheel for access. Then, detach the lower control arm by removing the bolts holding the ball joint in place. Replace the old ball joint with the new one, ensuring it’s properly seated, and reattach the control arm and tighten the bolts to the manufacturer’s specifications. Finally, reassemble the wheel and lower the vehicle.
How do you remove front rotor from 1998 Hyundai Elantra?
I have a 1998 Hyundai Elantra and had the rotors replaced, you will have to have a shop to do it because they have to be pressed off and then back on again with a specialized machine or tool. Of course unless you have that tool you can do it yourself. Good luck.
