answersLogoWhite

0

Most thermostats have a Jiggle pin. Its function is to allow trapped air past a closed thermostat as a build up of air in front of the wax capsule could cause engine damage. The wax capsule relies on coolant to relay heat to operate. If air was surrounding the capsule and the engine was at operating temperature, the stat would remain closed and cause the engine to overheat.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

Where is the thermostat in the 2001 Toyota Camry?

Follow the top radiator hose to where it enters the engine. The thermostat is in that housing. You will need a new gasket. Ask the parts guy how the thermostat is installed. Many thermostat have a "jiggle pin" which most be located correctly.Don't get wrench happy tightening up the thermostat housing fasteners. The proper torque on those fasteners is not much.


How do you replace the Thermostat on 2003 Mitsubishi Galant?

If it is the 4cly you need to remove your intake, unbolt the thermostat housing from the side of the block (it will be the one with the radiator hose going to it) pull the thermostat out. When replacing with a new thermostat MAKE SURE YOU INSTALL IT WITH THE JIGGLE PIN FACING UP!!!! I repeat JIGGLE PIN FACING UP. Burp the radiator system well and your done. Good Luck


What is a thermostat jiggle pin?

The Jiggle pin allowes any trapped air behind the thermostat to pass through. Without this the engine could overheat. The thermostat uses engin coolant to melt a wax capsule and allow coolant to pass. The engin could be at operating temp and the thermostat would not open due to air being in contact with the capsule instead of the actual coolent. This would most likely lead to an overheating engin, and damage.


How do you replace the thermostat on a 1994 mx3?

Follow the water hose to the distributor on the DOHC 4 cyl 1.6---the housing to be removed is a few inches from the distributor. Remove the distributor cap and other stuff if necessary. The Jiggle pin of the thermostat must face straight up when installed. Folow the thermostat included instructions. Acutemoon@phreego.com


How do you change the thermostat on a 94 Ford Probe?

Remove the Air Intake Box so you can see in below... there is a pipe running right into the bell where the thermostat is housed. There is one bolt that you need to take remove (it is to the right, below the distributor, it goes into the engine block). Then there are the other 12 mm bolts on the bell of the thermostat housing to remove. After removing those the thermostat should be able to come right out. When replacing i would recommend getting a replacement thermostat with a jiggle pin...


How do you change the thermostat on a 99 Mazda 626 v6?

Service and RepairTHERMOSTAT REMOVAL/INSTALLATION# Disconnect the negative battery cable. # Remove the ignition coil (KL). # Drain the engine coolant. # Remove in the order indicated in the table. # Install in the reverse order of removal. Thermostat Installation Note# Verify that the jiggle pin is aligned with the projection of the thermostat gasket as shown.# Install the thermostat into the thermostat case, aligning the projection on the gasket to the thermostat case as shown. Copyright © 2007 ALLDATA LLC


What is the pin on the thermostat on an Eclipse?

The pin is called a "jiggle" pin. It's there to allow the system to bleed off any air pockets that might be sitting above the level of the port on the T stat. The pin should always be pointing towards the top of the engine. Rick I'm a retired ASE Master/L-1 Technician. I still keep current with the latest automotive technology. Visit my blog for cool articles and TSB's: http://free-auto-repair-advice.blogspot.com


Draw a Z80 processor and explain five of its pin function?

draw the Z80 processor and explain five of its pin function


How do you remove rear rotors of a 96 Camry?

Remove the cotter pin/nut in center & they pull straight off.


How do you replace the thermostat located on a 1988 Mazda 626 4 cylinder automatic?

check autozone.com 2.0L Engine Disconnect the negative battery cable. Drain the engine coolant from the radiator to below the level of the thermostat. Fig. 3: To remove the thermostat, first drain the cooling system, then remove the radiator hose-to-thermostat housing cover clamp ... Fig. 4: ... by sliding back on the hose. Note the alignment marks on the hose and housing cover (arrows) Fig. 5: Disconnect the hose from the thermostat housing cover Fig. 6: Loosen the thermostat housing cover attaching bolts ... Fig. 7: ... then remove them ... Fig. 8: ... along with the housing cover/water outlet Fig. 9: Remove the thermostat from the housing by simply pulling it outward Fig. 10: When installing the new thermostat, note the tab (arrow) which seats into a notch in the housing. Jiggle pin must face straight up Disconnect the lower radiator hose from the engine. Remove the housing bolts, thermostat housing, thermostat and gasket. Do not pry the housing off. To install: Clean the thermostat housing and the cylinder head mating surfaces. Make sure that the thermostat jiggle pin is aligned with the gasket projection. Install the thermostat to the housing. Align the gasket projection with the opening in the housing. The spring side of the thermostat should face into the housing. Install the thermostat housing cover and tighten both bolts to 14-19 ft. lbs. (19-25 Nm). Fill the cooling system. Connect the negative battery cable, start the engine and check for leaks. Check the coolant level and add coolant, as necessary. FOR PICTURES GO TO: http://www.autozone.com/servlet/UiBroker?ForwardPage=/az/cds/en_us/0900823d/80/14/44/e4/0900823d801444e4.jsp


What is the function of each pin in a 3 pin XLR PLUG?

Pin 1 = ground, Pin 2 = hot/plus, Pin 3 = cold/minus


How do you bypass 1998 Camry lxe ilock security?

I removed the ilock security box on my 1998 Camry lxe. I need to repin or jumper the 8 pin molex connector. can you help? my email is y2kharold@comcast.net