answersLogoWhite

0

The idle speed for a 1992 Isuzu Rodeo with a 3.1 V6 engine is typically around 600 to 800 RPM when the engine is warm. However, it's advisable to check the vehicle's service manual or consult a professional for the exact specifications, as variations can occur based on specific configurations or modifications.

User Avatar

AnswerBot

2mo ago

What else can I help you with?

Related Questions

Why do the dash warning lights come on at idle on a 1997 Isuzu Rodeo?

Which lights?


How do you adjust idle speed on 89 rodeo?

To adjust the idle speed on a 1989 Isuzu Rodeo, locate the idle speed adjustment screw on the throttle body. Start the engine and let it warm up to operating temperature. Then, turn the adjustment screw clockwise to increase the idle speed or counterclockwise to decrease it, checking the RPM with a tachometer until you reach the desired idle speed, typically around 800-900 RPM. Always ensure that any adjustments comply with manufacturer specifications for optimal engine performance.


Why on my 1998 rodeo the rpm drops and engine stalls immediately after starting If I rev the engine and shift into gear with my foot on the gas it is fine?

I have the same problem with my 98 Isuzu Rodeo. If you haven't already, replace the Idle air control valve. I have the same problem with my 98 Isuzu Rodeo. If you haven't already, replace the Idle air control valve.


What causes a 2001 Isuzu Rodeo to start then die?

idle air control motor has to much build up of carbon, clean it


Idle setting for 1995 Isuzu Rodeo 3.2lt 4wd?

u dont set the idle the ecm does the setting througt the air idle conrtol. If it wont idle u need to replace the aic motor on the th0rottle body!


What are the Measurements for a valve adjustment on a 1992 Isuzu Amigo 2.3L?

Valve Clearance (Cold) Cold intake-0.15mm(0.006)" Exhaust-0.25mm(0.10)" Idle Speed- (900)rpm


Where is the idle control valve located on my 2002 Isuzu rodeo?

The idle control valve on a 2002 Isuzu Rodeo is typically located on or near the throttle body, which is situated on the intake manifold. To access it, you may need to remove the air intake duct and possibly some other components. It's advisable to consult a repair manual for detailed instructions and diagrams specific to your vehicle model.


How do you adjust idle speed on 1992 golf with carb?

To adjust the idle speed on a 1992 Volkswagen Golf with a carburetor, locate the idle speed adjustment screw on the carburetor. Start the engine and allow it to warm up, then turn the screw clockwise to increase the idle speed or counterclockwise to decrease it. Aim for the manufacturer's recommended idle speed, usually around 800-900 RPM for this model. Finally, recheck the idle speed after making the adjustment to ensure it is set correctly.


How do you adjust the idle speed on a 1992 Chrysler 5th Avenue?

Idle speed is computer controlled and is not adjustable. If the speed is incorrect check for a stuck idle speed air motor, on the throttle body, and for air flow problems.


What would cause a gas pedal to stick on a 1992 Isuzu rodeo?

Since it is a throttle body, check to make sure that the cable is not binding, if it is, replace it. If the cable is free moving, it is either the Idle Air Control valve, or the Throttle Position Sensor. Those are the most common culprits.


What is the correct timing for a 2001 Isuzu Rodeo 2.2?

The correct timing for a 2001 Isuzu Rodeo with a 2.2L engine typically refers to the ignition timing, which is generally set at 10 degrees BTDC (before top dead center) at idle speed. However, it's essential to consult the vehicle's service manual for precise specifications and procedures, as variations may exist based on engine condition and modifications. Always ensure that the engine is at the correct operating temperature when making adjustments.


Where is the transmission dipstick located on a 2001 Isuzu Rodeo sport?

On a 2001 Isuzu Rodeo Sport, the transmission dipstick is located near the back of the engine bay, typically on the passenger side. It is usually a yellow or red handle that is distinct from the oil dipstick. To check the transmission fluid, ensure the vehicle is on a level surface, and the engine is running at normal idle.