0
What else can I help you with?
How do you change transmission fluid on a 2005 Nissan Sentra?
take it to the dealership, a nissan sentra takes atf fluid you can only buy at the dealership. For how much the fluid and tools for it cost it will be about the same price for them to do it
What types of tools do I need to have so I can replace the spark plugs in my 1998 Nissan Sentra?
You will need a general screwdriver, a spark plug socket, a socket wrench and and extender, a wire brush and a silicone dielectric compound. You should find more of these tools at SEARS or your favorite car parts dealer. You will need a spark plug wrench with an extension to replace the spark plugs in a 1998 Nissan Sentra. You can find an instructional video at www.youtube.com.
What is needed to repair a leaking Rack and Pinion for a 2000 Corolla?
It requires some expensive special tools and specialized knowlage to repair a rack and pinion steering gear, it is easier and less costly to replace the rack and pinion with a remanufactured unit than to purchase the special tools to repair a rack and pinion steering gear
How do you replace the water pump on a 1988 Nissan Sentra and do you need any special tools?
Defective Water pumpI recently replaced my water pump on my 93 sentra.It's kind of easy if you know something about cars..take off right wheel,remove top pulley by removing the bolts the water pump is behind it.Then remove the bolts of the water pump itself.. Transporter..I'm not a member but i do a lot of work on my own cars,both are Nissan sentra's.
How do you replace water pump on Nissan primera?
To replace a water pump on a Nissan Primera one must obtain the proper parts, the proper tools, and the instructions made to fit the model of the machine.
Where is the oil filter located on 2013 Nissan Sentra?
On a 2013 Nissan Sentra, the oil filter is located on the engine block, typically near the front of the engine, close to the oil pan. It can be accessed from the top or bottom of the vehicle, depending on your approach. Make sure to use the correct tools and take precautions to avoid spills when changing the oil filter.
How much does engine servicing cost for a Nissan Sentra 1997?
it only cost me about $65. not hard to do you can do it you self all you nee are tools and you are good to go, i did it and i don't know anything about cars
What is the preload on the pinion bearing and the backlash on the crownwheel and pinion inside the rear differential of a 1997 ford explorer 4 wheel drive?
The shim between the inner bearing and the pinion is critical and if it's lost you need special tools to set the pinion depth. replace the bearings and seal with an new crush sleeve thighten the pinion nut until the sleeve crushes and you can't move the pinion up and down. Then very slowly tighten the pinion nut checking the rotational torque. You will need an inch pound torque wrench, when the preload is correct it should take between 20-25 inch pounds of torque to rotate the pinion. If you get it too tight you need to replace the crush sleeve and start over. Proper bearing preload and gear mesh are critical.
Tools needed to replace 2005 Nissan Xterra front brakes?
the only tools need are a 17 inch socket a rachet a "C" clamp to push the piston back in.
Is it easy to install a Rack and Pinion on a 98 Saturn SL?
No its not. It is diffcult even with proper tools.
How do you replace the head gasket located on a 1996 Nissan Sentra?
If you have to ask that question you shouldn't do it yourself as removing a cylinder head is not for the inexperienced. if you do decide to do it yourself make sure you have all the proper tools, and a repair manual, you'll need a full range of metric tools including a torque wrench. follow the manual for the rest of the instructions. Replacing the head gasket on any vehicle is a long and complicated process, however if you wish to see basic step-by-step instructions go to the related question on the right side of the page "How do you replace a head gasket?"
How do you replace a ring and pinion gear in a 1994 Z71 Chevy pickup?
it's best to get a shop to do it....unless you have all the specialty tools to do the job...if it isn't set up right....it'll be torn up in 6 months or less
