0
A grinding noise during acceleration in your Toyota Sienna could be caused by several issues, such as worn or damaged transmission components, a failing wheel bearing, or issues with the drive axles. It may also be related to problems with the brakes if they are engaged unintentionally. It's important to have the vehicle inspected by a qualified mechanic to diagnose the specific cause and prevent further damage. Ignoring the noise could lead to more serious mechanical issues down the line.
What else can I help you with?
Does the 1999 Toyota Sienna have an Interference Engine?
no. if the belt breaks just replace it making sure the cam timing is properly set
What year model is the 8 passenger Toyota Sienna?
The 8-passenger Toyota Sienna is available in various model years, with the most recent generation starting in 2021. This generation features a hybrid powertrain and advanced safety technology. The Sienna has consistently offered 8-passenger seating across its various model years, making it a popular choice for families.
What is the fuel tank capacity of a 2001 Toyota Sienna?
The fuel tank capacity of a 2001 Toyota Sienna is approximately 20 gallons (75 liters). This capacity allows for a decent driving range, making it suitable for family trips and longer journeys. Always consult the owner's manual for the most accurate specifications.
In your 2005 Sienna the front door driver side hinge is making a loud clunking noise when you open or close the door?
I have the same problem on my 05' Sienna. My mechanic showed me that it was the door hinge making the noise (soon your window will not open unless door is open). My mechanic said he has seen this before, but Toyota dealer has to fix it. They want $1K to fix, so we are living with it. Toyota is going down hill.
Your dodge Dakota is making a clicking noise only when accelerating What is it?
Its usually a U joint. Click under acceleration . While turning,a CV joint. Grinding or moaning is usually a bearing.
Where is the starter located on a 2003 Toyota Sienna?
The starter on a 2003 Toyota Sienna is located on the driver's side of the engine, near the bottom of the engine block. It is positioned between the engine and the transmission, making it somewhat difficult to access without removing other components. To reach it, you may need to lift the vehicle and remove the undercarriage cover or other parts for better access.
Can 22 rwd fit in 2011 Toyota Sienna awd?
No, 22-inch rims typically cannot fit on a 2011 Toyota Sienna AWD without significant modifications. The Sienna is designed to accommodate smaller wheel sizes, usually ranging from 17 to 19 inches. Installing larger rims could lead to issues with clearance, handling, and overall performance. Always consult a professional or refer to the vehicle's specifications before making such modifications.
Where are Toyota's made?
Toyota is made in dang Japan. For all you dummies who think its made in the USA its just manufactured over here retards which means put together here.
Would Toyota Sienna 04 rims fit dodge caravan 02?
No, the rims from a 2004 Toyota Sienna will not fit a 2002 Dodge Caravan. The bolt pattern, offset, and center bore specifications differ between these two vehicles, making them incompatible. It's essential to match these specifications when considering wheel interchangeability. Always consult a professional or refer to the vehicle's manual for accurate compatibility.
Where is the knock sensor for 2002 Toyota sienna?
The knock sensor for a 2002 Toyota Sienna is located on the engine block, specifically on the rear side of the engine near the transmission. It is typically mounted near the cylinder head, making it a bit challenging to access. To reach it, you may need to remove some components or the intake manifold for easier access. Always consult a repair manual for your specific vehicle for detailed instructions.
Your water pump is making grinding noise in 2001 dodge caravan?
The pump will need replaced if it is grinding.
Why is car making a grinding or rumbling type noise from the rear end of the car when under hard acceleration and stops when you let off the gas?
Have your mechanic check the rear bearings for the grinding noise. If the noise is like a rumble strip then the torque converter may be bad. Mark VIII are know for bad torque converters.
