Set Alarm One (1)
Hour: Press TIME button once to set Hour Alarm 1
Hold alarm on/off button until Hour blinks
Use up/down buttons for setting desired alarm hour
Finished: walk away
To return to MM/DD mode press
Press Alarm on/off twice
Press Time twice
Minutes: Press TIME button once, Hold alarm on/off button until hour blinks, release, press
alarm on/off button once until Minute blinks
Use up/down buttons for setting desired alarm minute
To go to Alarm 2
Alarm 2: Go to Set Alarm - Two (2)
Minute: Press TIME button once, Hold alarm on/off button until hour blinks, release, press alarm on/off button once until Minute blinks
Use up/down buttons for setting desired alarm minute
Finished: walk away
To Exit and Return to MM/DD mode
Press Alarm on/off twice
Press Time twice
To Set Alarm Two (2)
Press Alarm on/off twice
Press Time twice
Go too Set Alarm Two (2)
Set Alarm Two (2)
Hour: Press TIME button twice to set Hour Setting 2
Hold alarm on/off button until Hour blinks
Use up/down buttons for setting desired alarm hour
Finished: walk away
M/DD mode press
Press Alarm on/off twice
Press Time twice
Minutes: Press TIME button once, Hold alarm on/off button until hour blinks, release, press
alarm on/off button once until Minute blinks
Use up/down buttons for setting desired alarm minute
Minute: Press TIME button once, Hold alarm on/off button until hour blinks, release, press alarm on/off button once until Minute blinks
Use up/down buttons for setting desired alarm minute
Finished: walk away
To Exit and Return to MM/DD mode
Press Alarm on/off twice
Press Time twice
To set the day on a Sharp SPC900 atomic clock, you typically need to press the "Mode" button until the day setting starts flashing. Then, you can use the "+" and "-" buttons to adjust the day to the correct setting. Once you have selected the correct day, you can press the "Mode" button again to save the changes and exit the setting mode. Make sure to consult the clock's manual for specific instructions tailored to your model.
To set up a Sharp Atomic Clock Model SPC 502, first, insert the batteries and ensure they are properly seated. Next, place the clock in an area with good visibility to the signal and press the "Set" button to enter the time zone setting. After selecting your time zone, the clock will automatically search for the atomic time signal; ensure it remains in a location where it can receive the signal without interference. Finally, adjust any additional settings, such as alarm or display preferences, as needed.
To set a Sharp Atomic Clock SPC 900, first ensure it is placed in an area with good reception for the radio signal. Press the "SET" button to enter the setting mode, then use the "UP" and "DOWN" buttons to adjust the time and date. Once the correct settings are displayed, press "SET" again to confirm. The clock will automatically synchronize with the atomic time signal once it receives it.
To set a Sharp radio control atomic clock, first, ensure it is placed in an area with good reception, away from large metal objects or electronic devices. Press the "SET" button to enter the setting mode, then use the “+” or “-” buttons to adjust the time and date as needed. Once set, the clock will automatically synchronize with the atomic time signal, usually overnight, ensuring accurate timekeeping. If necessary, you can manually adjust the time by holding the "SET" button until the time flashes, then use the adjustment buttons.
To set the time zone on a Sharp SPC 1003 atomic weather station clock, first press the "SET" button to enter the setup mode. Use the "CH" button to navigate to the time zone setting, then adjust it using the "+" or "-" buttons until the desired time zone is displayed. Once set, press the "SET" button again to confirm your selection and exit the setup mode.
To turn off the alarm on an SPC900 Sharp atomic clock, press the "Alarm" button until the alarm time flashes on the display. Then, press the "Set" or "Mode" button to toggle the alarm off. Confirm that the alarm indicator disappears from the display, indicating that the alarm is deactivated. If needed, refer to the specific user manual for detailed instructions.
Temp does not display on Sharp Atomic Clock SPC 900
Press the down button on the back of the clock to go between 12 hour & 24 hour.
To turn off the alarm on a Sharp atomic clock, locate the alarm switch on the back or side of the clock and set it to the off position. Depending on the model, you may need to press a specific button or sequence to deactivate the alarm. Refer to the user manual for detailed instructions.
To set the day on a Sharp SPC900 atomic clock, you typically need to press the "Mode" button until the day setting starts flashing. Then, you can use the "+" and "-" buttons to adjust the day to the correct setting. Once you have selected the correct day, you can press the "Mode" button again to save the changes and exit the setting mode. Make sure to consult the clock's manual for specific instructions tailored to your model.
To reset a Sharp Atomic Clock model SPC900, first, remove the batteries to power it down completely. Wait for about 10 seconds, then reinsert the batteries. This should reset the clock, allowing it to synchronize with the atomic signal when it powers back up. If needed, you can also press the reset button located on the back of the clock using a small pointed object.
To switch the Sharp atomic clock SPC900 from 24-hour to 12-hour format, you typically need to access the clock's settings menu. Look for an option labeled "Time Format" or something similar, and then select 12-hour format. Refer to the user manual for specific instructions on accessing and changing this setting on your particular model.
YES. My deceased had the original
Don't no
If your Sharp alarm clock's alarm isn't going off, first check that the alarm is properly set and the time is correct. Ensure that the alarm switch is turned on and that the volume is at an audible level. If it still doesn’t work, try resetting the clock by unplugging it and plugging it back in. If the issue persists, consult the user manual for troubleshooting steps or consider contacting customer support.
To set up a Sharp Atomic Clock Model SPC 502, first, insert the batteries and ensure they are properly seated. Next, place the clock in an area with good visibility to the signal and press the "Set" button to enter the time zone setting. After selecting your time zone, the clock will automatically search for the atomic time signal; ensure it remains in a location where it can receive the signal without interference. Finally, adjust any additional settings, such as alarm or display preferences, as needed.
Oh, isn't that just a happy little question! To increase the volume on your sharp alarm clock, you can usually find a button or switch on the clock itself. It might be labeled as "volume" or have a speaker icon next to it. Just gently adjust it to the desired volume, and you'll be waking up to a cheerful sound in no time!