0
What else can I help you with?
Is coaxl input on tv HDMI?
The coaxial RF input on a HDTV will process a HD signal but it is not an HDMI input.
What's the best way to hook up a hdtv to a cable box?
A Cable box and TV are connected together through a RF cable.
Does a N64 have to have a RF modulator to use a RF switch?
Yes, a modulator is required if you use a RF cable to connect it to the TV.
Where is the freon port on a 2004 Ford Focus?
rf inner fender behind headlight
How do you turn a normal tv into HDTV?
Standard definition TV's really can't be changed into anything other than what they are. In other words, there's no conversion kits, etc. But a standard definition TV can still use the digital HDTV signals with the use of a converter box on your antenna system, Dish or DirectTV RF output jacks, etc. The picture, even though converted, will still generally look better than a standard analog signal just because there's quite a bit more information in the signal allowing your analog TV to wowrk at it's maximum capabilities.
Is rf equilibrium still active?
yes it is
Your HDTV does not have an hmdi input how should you connect your cable box to the tv?
In descending order of quality, Component, S-Connector then Video. The RF or antenna input is the poorest.
Can 2 substances with different Rf values still be similar?
Yes, two substances with different Rf values can still be similar. Differences in Rf values can be due to various factors, such as the polarity of the compound or the composition of the stationary phase. Therefore, substances with different Rf values can still share similar chemical structures or functional groups.
What is an RF isolator?
AN RF Isolator is really a three port device called an "RF Circulator" in which one port is always terminated correctly with a suitable load. RF Isolator are usually passive and are bandwidth limited.Typical use: It used in the output of a RF Transmitters High Power Amplifiers but before a BP/ HP filter and the antenna.Typical Function: To isolate a TX RF Power Amplifier output from receiving RF feedback from external sources. i.e. In this case the RF coupled in from other Antenna systems in close proximity. Such undesired RF feedback would cause intermodulation / harmonics products to be generated within the RF amplifier and consequently be re-radiated out along the the desired RF signal to the antenna and possibly cause interference. Often used on all TX's in two way radios sites to avoid local IM.SIMPLIFIED: In other words an Isolator passes RF in one direction but attenuates RF in the other direction.Note: The RF Isolator is slightly non linear and therefore it can cause low levels of intermodulation / harmonics. So it is good practice to place either a basic Band Pass or High pass filter after the RF Isolator to attenuate the unwanted IM products.Tuning these RF Circulators / Isolators correctly requires a suitable network analyzer or combination of RF Bridge / Spectrum Analyzer with Tracking generator.
What is an Rf?
AN RF Isolator is really a three port device called an "RF Circulator" in which one port is always terminated correctly with a suitable load. RF Isolator are usually passive and are bandwidth limited.Typical use: It used in the output of a RF Transmitters High Power Amplifiers but before a BP/ HP filter and the antenna.Typical Function: To isolate a TX RF Power Amplifier output from receiving RF feedback from external sources. i.e. In this case the RF coupled in from other Antenna systems in close proximity. Such undesired RF feedback would cause intermodulation / harmonics products to be generated within the RF amplifier and consequently be re-radiated out along the the desired RF signal to the antenna and possibly cause interference. Often used on all TX's in two way radios sites to avoid local IM.SIMPLIFIED: In other words an Isolator passes RF in one direction but attenuates RF in the other direction.Note: The RF Isolator is slightly non linear and therefore it can cause low levels of intermodulation / harmonics. So it is good practice to place either a basic Band Pass or High pass filter after the RF Isolator to attenuate the unwanted IM products.Tuning these RF Circulators / Isolators correctly requires a suitable network analyzer or combination of RF Bridge / Spectrum Analyzer with Tracking generator.
What if rf input and outputs are reversed on a TWT?
If the RF input and output are reversed on a traveling wave tube (TWT), the amplifier will not function correctly. The input signal would not be amplified but instead sent back out through the input port. This would result in no signal being output through the intended output port.
Does your new tv hAVe a AV port on it for your nes or do they not do that anymore?
You should be able to connect the RF adapter that came with you NES into the coaxial cable port on your tv even though you probably don't use that connection anymore for your cable or satellite connection. Then all you have to do is put your tv on the antenna/cable input and tune it to channel 3.
