Many television sets have a non-remote way to bring up a menu by either having a specific menu button (on newer t.v.'s) or by pressing a combination of two buttons. For instance, some t.v.'s menu appears when you press the next channel and previous channel simultaneously.
See if your TV has a menu button. If it does, hit that, then go to screen options, or captioning options. You would probably use the channel up/down to navigate. you will eventually find the caption off/on/on when muted option. If there is no menu button, you may need to get another remote or a universal remote.
Usually the CC options are found by hitting the MENU button, then going to screen options or caption options. If you dont have a remote, some TV's have a menu button, and you navigate them using the channel up/down button.
On my Sharp Linytron TV, there is Setup button on the front of the TV, click it. It will display a menu and one of the options is Air/Cable or Antennae/Cable. Click the Setup button until that menu option is selected. Click the down volume button to select it and enter the Air/Cable options. Click the up volume button to move the selection to Cable. Click the Setup button to accept the selection then again to move to the Exit option. Click the down volume button.
I have an Orion widescreen TV and i can bring up a menu which offers TV, AV1&2, Component, HDM1&2 and PC by pressing either the input select button on my remote or the first or second button on the left of the power button.
To reprogram channels on a Sony TV without using the menu, you can typically use the channel up/down buttons on the remote to navigate to the desired channel. Once you're on the channel you want to set, press and hold the "Enter" or "OK" button (depending on your model) until it confirms the change. Alternatively, you can use the "Favorites" button to save channels directly, if available. Be sure to consult your specific model's user manual for detailed instructions, as the process may vary.
You can program the DISH Network remote without the remote code, this can be done by completing a Power scan. I have included instructions to further assist you.With the desired equipment on, press and hold the correct Mode button (In this case the mode button will might be "TV") until all the other mode button back lights illuminate, then release.1. Press and release the Power button.2. Press the Up button once a second while pointing the remote at the desired equipment.Note: If the code for the equipment comes up, the equipment will power off.3. Press the POUND (#) button. If the code entered is valid for the remote, the mode light flashes three times.After completing the power scan to program the DISH Network remote to your T.V the remote should now work, you can try turning the volume up or down or powering the TV on or off.
There is a button located near the clutch pedal area up under the dash. It is a black button on a wire near the fuse box.
To turn off the child lock on a Technika TV without a remote, first, try pressing and holding the "Menu" button on the TV itself for several seconds. If that doesn’t work, you can also try holding down the "Volume Up" and "Channel Up" buttons simultaneously for a few seconds. If neither method works, consult the user manual for specific instructions related to your TV model or consider using a universal remote as a last resort.
To unlock the V-Chip on a television, a person will need to use the remote control. If there is a menu button on the television, this could be used to access the V-Chip. Push the Menu button, then navigate to parental controls using the up or down volume buttons.
To reprogram an Astrostart TX2000 remote, first, ensure the vehicle's ignition is in the "On" position without starting the engine. Press and hold the "program" button on the remote until the LED indicator lights up, then release the button. Next, press the button on the remote that you want to program, followed by the "program" button again to save the setting. Finally, turn off the ignition to complete the reprogramming process.
To change channels on an Artec digital to analog converter without a remote, use the buttons on the front panel of the device. Typically, there will be a channel up and channel down button that allows you to cycle through the available channels. If there is a menu button, you can access the channel list and select the desired channel using the navigation buttons. If your converter has a dial, you can also turn it to change channels.
The first thing you should do is call the front desk and ask for a remote. You could also just go up to the television and turn the power button on.