How do you hook up a smart TV to DISH dvr?

Is there a dish net dvr receiver that can be used without a fee?

Dish Network's DVR receivers typically require a subscription to access their services and record programming. While you can purchase a Dish DVR receiver, ongoing fees for programming and features like DVR functionality are generally part of the service plan. Without a subscription, the receiver may still function for basic TV viewing but won't provide DVR features or access to Dish Network channels. Always check with Dish Network for the most current policies and options.

Can I hook up any DVR to my old TV?

You can hook up to almost any television with the correct inputs, the age of the TV does not matter as long as the materials required to link are there.

How do you hook up satellite tv and still keep cable internet?

DISH is a leading satellite TV & internet provider offering the best programming and technology at an unbeatable value. Dish delivers the best video anywere at anutime utlizing state-of-the-art equipment & technology & award-winning HD & DVR Technology! cutt.ly/HhCPyNG

Can you hook a webcam up to a tv with out expensive hardware?

No. But you can buy cheap cams on the net, connect it to a DVR the plug it to the TV.

I have an old Dish DVR with recorded programs. I now use Time Warner Cable. Can I connect this dish dvr to my tv and or my DVD player and watch the recorded shows?

Absolutely you can watch your old recorded programs - provided that you still have the smart card that plugs into the Dish DVR. However, you cannot record programs, so do NOT attempt to connect the DVR to the Time Warner system in any fashion. DO NOT plug ANYTHING into the Dish DVR SATTELITE INPUT coaxial jack. There are several methods you can use to connect your old Dish DVR, depending on the model of the TV set. If it is fairly new then you should have multipul inputs on the back of the TV. Look for an open RCA input set. This would consist of one of each - red, white, and yellow round jacks grouped together. Look for the printed name designation next to the jack set (i.e. VCR, INPUT 1, INPUT 2, AV IN, AUX, etc.). On the back of the Dish DVR you will see the same three jacks labled OUTPUT, or OUT TO TV, or something like that. Now, if you were a good boy, or girl, you saved the RCA plug cable that was previously plugged in to the Dish DVR jacks. If not, look around the house for a set. If not, then its Radio Shack time for you. The clerk will know exectly what you need. The next step is to connect the TV and the DVR together with the RCA cable, making sure the plug colors match the jack colors. Turn on the TV and the old Dish DVR. If you did everything right then you TV should still be operating exactly like it was. Now grab the TV (not the Dish) remote control and figure out how to change the TV screen from TV to VCR, INPUT 1, INPUT 2, AV IN, AUX, etc.) There is definately a way to do it, so get someone to help you if you can't figure it out (but I know you can). Once you have the Dish DVR on the TV screen, grab old Dish remote (check the batteries) and off you go. When you're done watching your recorded program(s) switch back to TV mode using the TV remote. Another option, assuming that your Time Warner box is connected to your TV via a coax cable, will require a run to Radio Shack to buy a coaxial A/B switch and two short coax cables (or look around the house). Connect as follows: 1) Disconnect the Time Warner box's coax cable from the back of the TV and connect it to A/B switch jack A. 2) Connect a short coax cable to the TV (where Time Warner was plugged into) and the other end to the common (usually the center) jack of the A/B switch. 3) Connect a short coax cable to the Dish DVR OUT TO TV jack and the other end to the A/B switch jack B. Now turn on the TV and the old Dish DVR and you should be able to swith back and forth between the two using the A/B switch. Remember that the old Dish DVR takes a while to boot up. Another option is if both your Dish DVR and TV has an available HDMI jack. In that case, all you need is a short HDMI cable to connect the two, and then figure out how the TV remote switches your TV to the HDMI port. In all cases the old Dish DVR will say "Searching for Signal". This is the new normal. Just press the DVR button on the remote. Last of all - its just pretty much common sense. Hope this helps.

How do I set up on-demand with a DVR?

To set up on Demand to work with your DVR, hook up your HDMI cable and set up your DVR to work along with on demand. You can also call your TV service provider for additional help.

How do you hook up a playstation 2 to a dish network box my tv has no av or s video jacks?

It is very possible! I had Dish come and hook it up for me.

Will a dish dvr work on a direct tv?

Unfortunately, it is not possible to transfer saved programs between the two receivers

Is is possible to watch dish DVR files on another dish dvr?

Yes, as long as it is in your home. Also, it must be connected to one of the two TV's that you are sharing the receiver with. Hope this helps!

Which Satellite Receiver's can you record with, like the Tivo does?

Both direct tv and Dish Network offer a DVR tryp receiver.

How do you hook up a DVR when you have a satellite TV box?

The following procedure may vary, depending on if you have Dish Network or DirecTv. Connect one or two tuners to the "satallite in" on your DVR. Two is necessary in order to record two shows at once. Then, if you are working with standard definition, connect a yellow composite cable as well as two RCA audio cables to the TV and DVR. If you are working with High Definition, connect a set of component cables (blue, green, red) as well as two RCA audio cables to the DVR and TV. Also, you can connect an HDMI cable to the TV and DVR, which allows for HD video and audio to your tv with one cable. For more info on these cables and what they do, go into your local electronics store. Hope this helps and good luck!

How do you hook up a RF modulator and dvr?

To hook up an RF modulator to a DVR, start by connecting the DVR's audio and video output (usually composite or RCA cables) to the input of the RF modulator. Next, connect the RF modulator's coaxial output to your TV's coaxial input. Finally, set the TV to the appropriate channel (usually 3 or 4) that the RF modulator is configured to transmit on, and you should be able to see the DVR's output on the TV. Make sure all devices are powered on and properly configured for best results.