1. Manually turn on the component you want the remote to control (TV, VCR, DVD, satellite receiver or cable box). Note: If you press an invalid key during the Manual Code Search, the remote does not respond and the LED indicator light does not blink. If you do not press a valid Manual Code Search key (TV, VCR, DVD, SAT·CBL, ON·OFF, GO BACK), the search times out after two minutes. When the search times out, the LED indicator light blinks four times and turns off. The last programmed code under that component key is retained. 2. Press and hold the component key (TV, VCR, DVD, SAT·CBL) you wish to program. The LED indicator light turns on and remains on. 3. While holding the component key down, press and hold the ON·OFF key. The LED indicator light turns off. 4. After holding down both keys for three seconds, the LED indicator light turns back on. 5. Release both keys. The LED indicator light remains on. Throughout the programming of each key, be sure to keep the remote pointed at the IR sensor of the component you are currently programming the remote to control. 6. Press and release the ON·OFF key repeatedly until your component turns off. Each time you press the ON·OFF key, the LED indicator light blinks, and the next code in the list is sent. This process continues until all of the codes in the Code Lists have been searched. If your component turns off, you have found the correct code. (If it cycles through and the LED indicator light blinks four times and turns off, all codes have been searched. The Manual Code Search method is exited.) Press Stop when TV turns off.
The codes we here at DISH Network have & would use to attempt to program the DISH Network remote with your Olevia TV would be, 506 or 127.
To program your Dish Network remote for the SA WCT350, you can try the code 1004. If that doesn't work, you can also try 1005 or 1006. For further assistance, refer to the Dish Network remote control programming guide or the customer support for additional codes.
There are several different remote codes we have on file to program the DISH Network remote to work with your Symphonic TV that you can try the codes you can try are, 632, 569, 733, or 281.
There are several different remote codes we have on file to program the DISH Network remote to work with your Symphonic TV that you can try the codes you can try are, 632, 569, 733, or 281.
You can program your DISH remote to work on other electronic equipment. The gyration remote should have instructions on how to program it to other components. If you don't have the instructions, I would give the company a call to try and get the instructions.
You can program your DISH remote to work on your TV and other electronic components but unless you have codes or instructions on how to a universal remote to the receiver, we don't have codes specifically to operate in that manner. I would contact the manufacturer of your remote.
To program a Dish Network remote to control an Apex AD-500W DVD player, you can try using the code 504. If that doesn’t work, you can also try 505 or 506. If none of these codes work, refer to the Dish Network remote user manual for additional codes or the code search method to find the correct one.
To program a Dish Network remote to control a Cielo device, you typically need the specific TV code for Cielo. Commonly used codes include 10178, 10179, and 10180, but these can vary based on the remote model. You can find the exact code by accessing the Dish Network remote setup menu and selecting the appropriate device type. If the codes don’t work, consult the Dish Network website or user manual for additional assistance.
Try these remote codes: 743, 744, 745, 757. If these do not work, call Dish Network they will be happy to assist you.
No, the dish network remote only has those codes. If you want to control everything, get a Logitech Harmony remote.
Call the Dish Network to inquire about your remote and your new TV: 1 866 869-3109 Customer service can advise you and provide a new remote control if needed.
Some universal remotes can be programmed to work on the DISH receiver but you won't be able to use your Samsung TV remote to operate your DISH receiver. You can program your DISH remote to work your Samsung TV. I have provided instructions on how to program your DISH remote to your TV. I have also provide TV codes.TV codes: 738, 680, 516, 679, 666, 573, 665, 667, 669, and 653Remotes: Basic (Television Only)Turn the Television On.Press and hold the clear TV button for three seconds until the LED flashes.Enter the three-digit code using the buttons on the number pad.Press #. Note: The LED will flash three times.Test functionality with the TV.Return to Step 2 if the remote is not able to turn the TV On/Off, change the volume and mute the television.Possibly, depends on the remote