0
the ohm is a unit of measurement based off of someones last name. When used in subwoofers, for example 4 ohms or 8 ohms, it actually determines the amount of watts the speaker needs. Like if two identical subwoofers were taken and one was 4 ohms and one 8 ohms and applied say 150 watts to each of them, the 4 ohm would be louder because ohms are the speakers resistance and the lower the ohms the less amount of power it takes for the subwoofer to reach a specific loudness. That's why professional huge subwoofers may be one ohm, because an amplifier that has less power than the sub could still power it because since its one ohm, the 500 watt amplifier at 4 ohms could be 1500 watts at 1 ohm.
What else can I help you with?
Yes this amplifier works with a variety of subwoofers with various ohm loads. The amplifier will product the same power at 1.5 - 4 ohms making this a great choice for most subwoofers. ?
Yes this amplifier works with a variety of subwoofers with various ohm loads. The amplifier will product the same power at 1.5 - 4 ohms making this a great choice for most subwoofers.
Can you run two eight inch subwoofers requiring 50-100 watts of power each running at 4 ohms with a 2 channel 4 ohm amp putting out 75 watts per channel without damaging the subwoofers or the amp?
Yes
What amp should you use to power your subs?
The ideal amplifier for your subwoofers depends on their power handling and impedance ratings. Generally, you should choose an amp that delivers power within the subwoofers' RMS (Root Mean Square) rating for optimal performance without distortion. Additionally, make sure the amp's output matches the subwoofers' impedance (e.g., 2 ohms, 4 ohms) to ensure efficient power transfer and avoid damaging the equipment. For best results, consider an amplifier specifically designed for subwoofer use, often labeled as a "subwoofer amplifier."
Are type R subwoofers good?
Type R Subwoofers are generally accepted to be decent subwoofers.
Can I power 2 12 kicker comp 12 with a JBL GTO3501 amp?
Yes, you can power two 12-inch Kicker Comp subwoofers with a JBL GTO3501 amplifier, provided the subwoofers' impedance matches the amplifier's output. The GTO3501 is capable of delivering up to 350 watts RMS at 2 ohms, which should be sufficient for the Kicker subwoofers, as long as they are wired correctly (typically in parallel for dual 4-ohm subs). Make sure to check the power handling specifications of your specific Kicker model to avoid overloading the subwoofers.
Do all subwoofers have their own power source?
Most subwoofers have their own power source. There are subwoofers called "passive" woofers that will be powered by your amplifier.
What Car Subwoofers will work in aMercedes SL500?
Mercedes uses Bose subwoofers.
Are subwoofers just for cars?
No, subwoofers are for DJs, home theater, clubs, concerts, cars, etc... Subwoofers are for everybody who enjoys the low frequencies of the bass.
Will a mtx thunder 3401 amp work good with 2 12 kicker cvr?
Yes, the MTX Thunder 3401 amp can work well with two 12-inch Kicker CVR subwoofers, provided that the amp's power output matches the subwoofers' requirements. The Thunder 3401 typically delivers around 340 watts RMS at 2 ohms, which aligns well with the Kicker CVR's specifications. However, ensure that the subwoofers are wired correctly to achieve the optimal impedance for the amp to maximize performance without risking damage.
Will a library have information on audio subwoofers?
Your library should have a book that will contain information about audio subwoofers. You can first try searching the subject 'subwoofers' on the computers at your library.
No, this has nothing to do with Audio or Subwoofers. Its for serial devices.?
No, this has nothing to do with Audio or Subwoofers. Its for serial devices.
You have an Alpine type X 1243D subwoofer you are trying to decide if running it at a 2ohm load at max power or a 4ohm load at two thirds of its power range will work better?
Multiple subs wired together must be the same coil type and impedance. If they’re not, the power won’t divide evenly between them, and some subs would probably be over-powered while others get under-powered. If you want to run different types of subs in a system, each type needs to have its own separate amp. Then, multiply the number of subs you have by the RMS rating of each, to get their total RMS rating. You want to make sure the amp you choose will supply no more than the sub system’s total RMS rating. Figure out the possible total impedance(s) that the subs can be wired together to form. (SVC = single voice coil, 1 pair of terminals; DVC = dual voice coil, 2 pairs of terminals.) 1 SVC 2-ohms can only have 2 ohms of impedance 1 SVC 4-ohms can only have 4 ohms of impedance 1 DVC 2-ohms can have 1 ohm or 4 ohms of impedance 1 DVC 4-ohms can have 2 ohms or 8 ohms of impedance 2 SVC 2-ohms can have 1 ohm or 4 ohms of impedance 2 SVC 4-ohms can have 2 ohms or 8 ohms of impedance 2 DVC 2-ohms can have 2 ohms or 8 ohms of impedance 2 DVC 4-ohms can have 1 ohm or 4 ohms of impedance 3 SVC 2-ohms can have 6 ohms of impedance 3 SVC 4-ohms can have 1.3 ohms of impedance 3 DVC 2-ohms can have 1.3 ohms or 3 ohms of impedance 3 DVC 4-ohms can have 2.7 ohms or 6 ohms of impedance 4 SVC 2-ohms can have 2 ohms or 8 ohms of impedance 4 SVC 4-ohms can have 1 ohm or 4 ohms of impedance 4 DVC 2-ohms can have 1 ohm or 4 ohms of impedance 4 DVC 4-ohms can have 2 ohms or 8 ohms of impedance Look for an amplifier that can put out power up to the RMS wattage at an impedance load the subs can be wired to form. 8 ohms — figure on the amp putting out half the power it would at 4 ohms 6 ohms — figure on the amp putting out three-quarters of the power it would at 4 ohms 3 ohms — figure on the amp putting out the average of what it would at 2 ohms and at 4 ohms 2.7 ohms — figure the same as for 3 ohms, and add a few watts 1.3 ohms — use the 1-ohm spec and take away a few watts Example: You have two Alpine S Series S-W8D4 8" subwoofers and you want the right amp for them. They are DVC 4-ohm subs rated at 300 watts RMS each. Two 300 watts RMS subs together need a maximum total of 600 watts RMS. Using the chart in Step 2, 2 DVC 4-ohm subs can be wired together to form a 1-ohm, a 4-ohm, or a 16-ohm load. The last is too high a load to be practical, so you’ll look for an amp that can put out up to 600 watts RMS into either a 4-ohm load, or a 1-ohm impedance load: up to 600 watts RMS x 1 at 4 ohms, or up to 600 watts RMS x 1 at 1 ohm Among Crutchfield’s selection of amplifiers you’ll find: Memphis Audio PRXA600.1 — 600 watts RMS x 1 at 1 ohm JL Audio JD1000/1 — 600 watts RMS x 1 at 4 ohms Kicker KEY500.1 — 500 watts RMS x 1 at 1 ohm Any one of these high-quality amplifiers would work well with those subs. It doesn’t matter which impedance an amp plays through — 600 watts RMS through a 4-ohm load produces the same volume as 600 watts RMS through a 1-ohm load. You have a Memphis Audio SRX500D.1 amplifier and you want it to drive two subwoofers The amp is capable of 350 watts RMS x 1 at 4 ohms and 500 watts RMS x 1 at 2 ohms. Let’s say you choose to maximize the amp’s potential and want the system to put out 500 watts RMS. This means your subs have to be wired to form a total impedance of 2 ohms. Two subs on a 500 watts RMS amp will want about 250 watts RMS each. So you’ll look for subs each rated for 250 watts RMS or more. Using the chart in Step 3, for two subwoofers, a final 2-ohm load can be achieved with either two SVC 4-ohm subs or two DVC 2-ohm subs. So, you’ll look for two subs that are either SVC 4-ohms or DVC 2-ohms, rated for at least 250 watts RMS each: 2 SVC 4-ohms, at least 250 watts RMS, or 2 DVC 2-ohms, at least 250 watts RMS Among Crutchfield’s selection of subwoofers you’ll find: You have a Memphis Audio SRX500D.1 amplifier and you want it to drive two subwoofers The amp is capable of 350 watts RMS x 1 at 4 ohms and 500 watts RMS x 1 at 2 ohms. Let’s say you choose to maximize the amp’s potential and want the system to put out 500 watts RMS. This means your subs have to be wired to form a total impedance of 2 ohms. Two subs on a 500 watts RMS amp will want about 250 watts RMS each. So you’ll look for subs each rated for 250 watts RMS or more. Using the chart in Step 3, for two subwoofers, a final 2-ohm load can be achieved with either two SVC 4-ohm subs or two DVC 2-ohm subs. So, you’ll look for two subs that are either SVC 4-ohms or DVC 2-ohms, rated for at least 250 watts RMS each: 2 SVC 4-ohms, at least 250 watts RMS, or 2 DVC 2-ohms, at least 250 watts RMS Among Crutchfield’s selection of subwoofers you’ll find: Alpine W10S4 10" — SVC 4-ohm, 250 watts RMS JL Audio 12W0v3-4 12" — SVC 4-ohm, 300 watts RMS Kicker 44CWCS104 — SVC 4-ohm, 300 watts RMS Rockford Fosgate R2D2-10 10" — DVC 2-ohms, 250 watts RMS Hope this helps! (:
