0
To properly power two 600-watt speakers, you'll want an amplifier that can deliver at least 600 watts per channel at the speakers' impedance (usually 4 or 8 ohms). A good rule of thumb is to choose an amp with a power rating of 1.5 to 2 times the speaker's RMS rating for headroom and to avoid distortion. Therefore, an amplifier rated between 900 to 1200 watts per channel would be ideal for optimal performance. Always check the compatibility of the amp with your speakers' impedance and power handling specifications.
What else can I help you with?
You are looking for speakers for DJing and you have a 600 Watt amp. What kind of speakers do you buy?
With 600 watts, you can't really go too big, and if you only have one amp, you can't go with separate mids/highs and a sub, so personally, I would try to find a pair of 200 watt speakers that have nice tweeters, mids, and lows, all in one. Don't go for anything over 200 watts each, because you want to leave room on your amp. You don't want to get two 300 watt speakers, because your amp will be working at full power, which isn't good for it or your new speakers. So all in all, a nice pair of 200 watt full range speakers is what I would be looking for.
Can you use a 450 watt amp on 600 watt speakers?
Yes, if you don't turn it up all the way. Excessive power to speakers will result in distortion and possibly even complete failure of the voice coil and/or cone.
What is louder sub on 300 watt amp 10'' 300 watt or 10'' 600 watt?
They can be as loud, as the amp is not delivering 600 watts. The 10" sub rated at 600 watts is able to withstand more power.
Can a 350 watt amp power 2 12s?
It depends on the power and impedance rating of the 12-inch speakers. If both speakers are rated for 175 watts and the amp can handle the impedance of the speakers, then the 350 watt amp should be able to power both speakers effectively.
Can you use 2x500 watt subs on a 600 watt amp?
Absolutely!! If you turn up the gain too much, the speakers will smoke. You can use it at a lower level
What should the low pass filter be set to?
If it is a subwoofer amp then set it at about 80 hz.
Can you blow out your speakers if you use the wrong power amplifier?
Speakers can be blown if the wrong power amplifier is used and damage can be done by either overpowering or underpowering the amp. For example, if the power rating of the speaker is 300 watts capacity you will need a 300- to 600-watt amp.
What size amp do you need for 6 and a half Sony speakers that has 190 Watt peak power and 40 rms and Sony 6 by 9 speakers that has 300 Watt peak power and 60 rms?
200 RMS 4 channel or 2 channel so u know add the rms of the speakers to find the amp rms needed
Can a 250 watt amp push 1300 watt subs?
In most cases, the speakers should be able to handle more watts than the amp can deliver. Doing it the other way around will blow out the speakers.
Can 270 watt speakers damage a 125 watt amp?
Not unless the speakers are rated at a resistance (ohms) that is incompatible with the amp. Speakers don't generate power, the rating only tells you how much they can handle. So, speakers capable of up to 270 watts, can certainly handle 125 watts. However, if the amp is not 1-ohm stable and the speakers are 1-ohm, you could cause the amp to cut out and overheat depending on the protection mechanism of the amp.
What are the standard size safety switches up to 600 Amp?
30,60,100,200,400 and 600 amp
What are standard size safety switches up to 600 amp?
30,60,100,200,400 and 600 amp
