0
Air bag light blinks 3 times all the time when 1993 aerostar is running any way to reset?
The way to reset the light is to have the problem fixed. The blinking light indicates a problem with the SRS. If your air bag light is blinking,does horn or cruise work?If not the problem is the wiring contact in steering column.This is a wiring harness that runs through the column and is a Ford part. Probably not good for a do it yourself project as it is alot of labor and you must beware of deploying air bag when working on steering column. i had the same thing on my 91 when i took it in it was the air bag sensor in the stering colium this also works the horn as i later found out when i stoped working if you are to change it your self you must un hook the battery so you do not set the air bag off, to get at it you must remove the steriring wheel with a puller, it takes only about an hour to do the job.
What else can I help you with?
How can I reset a LiftMaster remote?
To reset a LiftMaster remote, you can usually press and hold the "learn" button on the garage door opener until the indicator light blinks. Then, press and hold the button on the remote you want to reset until the light on the opener blinks again. This should reprogram the remote to work with the opener.
How do you reset Brita filter light indicator?
To reset the Brita filter light indicator, press and hold the reset button on the pitcher or dispenser for about 5 seconds until the light blinks and then turns off. If your model doesn't have a reset button, simply remove the filter and reinstall it, which can also trigger the reset. Make sure to consult the specific instructions for your Brita model, as the process may vary slightly.
How can I reset a Hunter fan remote?
To reset a Hunter fan remote, you can usually press and hold the fan's power button for about 5-10 seconds until the light on the remote blinks. This should reset the remote and allow you to reprogram it as needed.
How can I reset my Hunter fan remote?
To reset your Hunter fan remote, you can usually press and hold the fan's power button for about 5-10 seconds until the light on the remote blinks. This should reset the remote and allow you to reprogram it as needed.
How can I reset my garage code?
To reset your garage code, locate the reset button on the garage door opener unit. Press and hold the reset button until the indicator light blinks. Enter a new code on the keypad and press the enter button to save the new code.
How do you reset the maintenance light on a 1996 Acura RL?
To reset the maintenance light on a 1996 Acura RL, first, turn the ignition to the "ON" position without starting the engine. Next, press and hold the "Select" and "Reset" buttons on the instrument panel until the maintenance light blinks and then goes off. Release the buttons, and the maintenance light should be reset. Finally, turn the ignition off and then back on to ensure the light remains off.
How can I reset the LiftMaster wall control?
To reset the LiftMaster wall control, locate the "Learn" button on the control panel. Press and hold this button for about 6 seconds until the LED light blinks. Release the button and the wall control should be reset.
How do you reset service massage for Volvo s 80?
Ignition to Pos1 Push and hold in odometer reset button Ig switch to Pos2 Wait until service light blinks, then release odometer button
How can I reset the garage code?
To reset the garage code, locate the reset button on the garage door opener unit. Press and hold the button until the indicator light blinks. Then, enter a new code on the keypad and press enter to save the new code.
How do you reset the service light on your 2001 Renault Megane 1.6 16v automatic hatchback?
To reset the service light on a 2001 Renault Megane 1.6 16v, turn the ignition key to the "On" position without starting the engine. Press and hold the trip reset button on the dashboard until the service light blinks and then goes out. Release the button, turn off the ignition, and start the engine to ensure the service light is reset. If the light remains on, repeat the process.
How do you reset change oil light for Suzuki burgman 400 motorcycle?
To reset the change oil light on a Suzuki Burgman 400, first, turn the ignition key to the "ON" position without starting the engine. Then, press and hold the "reset" button on the instrument panel until the oil change light blinks and then turns off. Release the button, and the light should be reset. Finally, turn off the ignition and start the motorcycle to ensure the light remains off.
Location of the tpms reset on Toyota RAV4?
The reset switch for me is a button to the left of the steering wheel facing diagonally downward. It has the symbol on it that resembles the dashboard indicator light. Hold his down until the light blinks 3 times, then release. If you hold it down and the light only disappears, that's not really resetting the light.
