answersLogoWhite

0

Yes, worn tie rod ends will make an alignment impossible and if the alignment was done with that sides tie-rod end compressed(clearance taken out) it will pull to that side while driving.

User Avatar

Wiki User

9y ago

What else can I help you with?

Related Questions

When the brakes are worn on only one side of the car the car might do what?

Assuming I understand your question: The brakes are worn on one side because they are only or primarily working on that side. This should cause the car to pull toward that side when braking.


Is it dangerous if your tie rod ends are not good on a 2002 Honda Civic ex?

Yes, it is very dangerous. If the tie rod is worn and it come loose you will loose all steering control and will have an accident which could result in death. Do not drive any vehicle with worn tie rod ends.


Why would your vehicle pull to one side when braking even though it stops ok?

It might have a caliper sticking, or worn brake pads. This can also be caused by bad ball joints. If that doesn't help, you may need an alignment. Check to see if it pulls when driving also. It won't pull as hard as when you stop, but if it does the alignment is off. Low tire pressure on the suspect side can cause the car to pull under braking. Possible contamination.


A vehicle pulls to one side during straight-ahead driving Which of the following conditions COULD cause this?

a tire low on air a different size tire a brake dragging loose/worn steering and suspension components such as tie rod ends or ball joints alignment


Why doesn't my chainsaw cut straight?

There could be a couple of reasons why a chainsaw may "pull," or, not cut straight:Cutters are sharped to uneven legnths or angles. If the angles (pitch) of, say, the left-side cutters are a different angle or size of the right-side cutters, the chain may want to pull itself over to one side resulting in an uneven cut. Likewise, longer right-side cutter plates would cause the cut to pull this way instead of staying straight (the pull will move in the direction of the bigger cut). Teeth can be filed or ground to be more even - a well-worn chain may simply need to be replaced.Bar rails are unevenly worn. If one of the bar rails is worn out more than the other, the chain would not sit flat, wanting to pull toward the worn side. To fix this grind your bar rails even or flip your bar over and use the other side.Bar rail groove itself is worn out. If there is a lot of side to side play while your chain sits on the bar good chance your groove is worn out. Grab the chain and try to move it side to side. There should not be a whole lot of play. If there is, take the bar into a saw shop and have the grind and hammer the bar. This will bring the groove back to the size it should be. Or, purchase a new guide bar.


Why is one side of my side pull brakes not moving properly?

One side of your side pull brakes may not be moving properly due to issues such as misalignment, worn out brake pads, loose cables, or dirt and debris buildup. It is important to inspect and troubleshoot these potential causes to ensure proper functioning of your brakes.


What side dose the flag is worn?

what side of the jacket is the flag worn on.


What is causing your car to pull to the right?

Usually, any time a vehicle "pulls" either to the right or left, it's caused by an alignment problem or worn ball joints.


Why does car shake in wind?

Your tie-rod ends or ball joints are probably badly worn. Or it could just be air friction pushing your car to one side.....


How can I reduce or eliminate side-to-side play in the rear wheel of my vehicle?

To reduce or eliminate side-to-side play in the rear wheel of your vehicle, you can check and tighten the wheel bearings, inspect and replace any worn or damaged components in the suspension system, and ensure that the axle and hub are properly aligned. Regular maintenance and proper adjustments can help improve the stability and performance of your vehicle's rear wheel.


What would cause front wheels to wobble side to side at 40-45 mph on 95 gmc?

Worn out tie rod ends ,idler arm, and Pittman arm would be the most suspectted culprits, but control arm and stabilizer arm bushings are also contributors to wobbling front ends!


Which side of the body is the m50 mask worn?

it is worn on the LEFT side of the body, also (TRUE)