0
What else can I help you with?
How would you connect 1- 4 ohm 40 watt speaker and 1- 6 ohm 35 watt speaker to left output of an AV receiver with 8 ohm and 110 watt output. Same combo for right output?
The 2- 4 ohm speakers can be hooked up in series to make 8 ohms. you cant hook up the 2- 6 ohm, cause if you put them in series, you have 12 ohms. If you put them in , parallel you have 3 ohms out from av to +(4ohms), -(4ohms) to +(4ohms), -(4ohms) to - av. And do the math 4ohms plus 4ohms equals 8ohms. doing the math on the 2- 6ohm speakers... 6ohms + 6 ohms = 12ohms I dont think 12ohms would blow your system, but it wont sound right. now if you raise the volume too loud on the av you will blow the speaker coils out you may boost the wattage of the 2-4ohm speakers (in series) to maybe 70 watts total ******************************************* If you connect loudspeakers in series, the amplifier can not properly damp them, but, unless you are a fairly critical listener, you perhaps won't detect the difference. Connecting two 6 ohm 'speakers in series will give a load of 12 ohms, and will not "blow" anything. Connecting a load impedance higher than the amplifier's design load will do no harm at all. The only disadvantage is that the amplifier will not be able to develop its rated power output.
How do you hook up your receiver to 13 speakers built in your home?
Running all these speakers at the same time might damage the amplifier. There are switchers made to handle this task.
How can you wire 2 12inch pioneer subs dvc 4ohms 1000 watts max to 2 pioneer 760 watt amps both amps are 2 channel they can be bridged?
You do pos to one side to pos the other side on the sub then the same for negative then to the amp you hook the pos to one channel then the negative to the other channel and the same on the other sub and amp
Is 275w root mean squared speaker can be use in 120w root mean squared amplifier 4ohms?
Yes. The "275W" is the maximum power that the speaker can handle at its input. The "120W" is the maximum undistorted power that the amp can deliver in the loud spots with the volume wide open. So the amplifier will never overdrive the speaker. The impedances of the speaker and amp-output should match. If one of them is marked "4 ohms", then they both should be. If they're not the same, then . . . -- the speaker may not sound as 'crisp' as it should. -- the amplifier may not deliver as much undistorted power as it should. -- the amplifier may not run as cool as it should. -- with an extreme mismatch and extended loud spots played at high volume, the amplifier may even be damaged.
Is it power amplifier and inverter both are same?
No
Can an electric-acoustic guitar be plugged in to a amplifier?
Yes. An acoustic-electric guitar plugs into an amplifier the same way a regular electric guitar does.
How do you hook a amp to a aftermarket radio in a 2002 Tahoe?
Amplifier instalation is the same as any-- power wire, ground wire, wires to subwoofer. The "tricky part is taping into existing wires to get the required input signal and the remote signal to switch the amp on and off.
Yes this amplifier works with a variety of subwoofers with various ohm loads. The amplifier will product the same power at 1.5 - 4 ohms making this a great choice for most subwoofers. ?
Yes this amplifier works with a variety of subwoofers with various ohm loads. The amplifier will product the same power at 1.5 - 4 ohms making this a great choice for most subwoofers.
Can you connect a turntable to a guitar amplifier?
You can, but it just will not have the same sound quality.
Can you hook up several speaker to the same port?
No. All amplifiers have a current limit and a minimum impedance rating. Most home stereos cannot connect more than 2 8 ohm speakers in parallel. Connecting more can seriously damage the amplifier.
How can I connect two guitars to a single amplifier using a Y cable guitar?
To connect two guitars to a single amplifier using a Y cable guitar, simply plug the two guitars into the two ends of the Y cable, and then plug the single end of the Y cable into the input of the amplifier. This allows both guitars to be played through the same amplifier at the same time.
Why RC coupled amplifier is called audio amplifier?
Because radio control relies on different frequencies. Since frequencies are involved in the process, an audio amplifier can be used to amplify alternating currents (currents that change), and it does the same job.
