0
yes you can turn the flywheel w/o it. Just before you put the distibutor in you need to make sure that you number one piston is at top dead center. you need to make sure your roter button is turned right, and your vacume should be pointed between the number 6 and number 8 spark plug
What else can I help you with?
How do you rotate the flywheel on a 1989 Chevy Suburban?
There is a big bolt that is inside of the bottom pulley on the front of the engine, It is the bolt that holds the balancer on . Get a socket that fits that bolt and then turn the engine with that and that will rotate the fly-wheel.
Can a rusted flywheel cause the engine not to turn over?
No, a rusted flywheel will not cause the engine not to turn over.
How do you advance the timing on a 1974 dodge dart slant 6?
find the distributor and at the bottom of it there is a bolt that you loosen that loosens the hold down plate that keeps it tight against the engine block, once you loosen the bolt the distributor will turn right or left, start the engine and then slowly turn the distributor one way or the other until you hear the engine RPM increase, when it increases you are advancing the timing.
How can the flywheel be turnedon a frozen engine to turn the engine?
If the engine is froze up, the flywheel can't be turned. You can use a socket and breaker bar on the crankshaft bolt, work it back and forth in both directions and it might break loose, but I wouldn't count on it. Usually you have to take the caps off of the connecting rods in order to turn the crank.
How do you adjustment the idle on 1992 gmc vandura 1500?
Through the carburetor or advance or retard the distributor by turning the distributor cap barely left or right. If you cant turn it then loosen the bolt holding the distributor on to the intake with a wrench then turn the distributor til the engine sounds like its not missing or not to where it's about to turn off.
Will a bad flywheel cause a car to not turn over?
A bad flywheel can definitely cause the engine not to turn over. The flywheel has teeth. If the teeth are chipped or broken, then the starter can not engage to spin the engine over.
How do you set the timing for a 1992 Mazda pick up B2000?
Like most vehicles with a settable timing. You need a timing light and a piece of chalk. The proper setting must be obtained from your manual. It will be something like 10 degrees before or after TDC(Top Dead Center). Connect timing light, mark zero degree on flywheel with chalk. You may need to spin flywheel a little and clean it off to see marks. After marking zero with chalk, start engine and allow to warm up to normal operating temp. loosen bolt holding ignition(distributor) and turn distributor and hold trigger on timing light and aim at flywheel chalk mark. Move distributor so timing light hits chalk mark exactly. Tighten distributor bolt and recheck alignment. You are done, shutoff engine and unconnect light.
Which way do you turn the distributor on a ford 302 to advance the timing?
Loosen the distributor hold-down bolt. Standing in front of the vehicle looking at the engine turning the distributor clockwise advances the timing. Turning the distributor counter-clockwise is retarding the timing. Hold the distributor steady while tightening the hold-down bolt. Factory hold-down bolt needs a 1/2 inch wrench.
How do you turn the distributor on a 1987 Chrysler Fifth Avenue 318 engine?
Loosen distributor clamp located at the base of the distributor with 1/2 socket on a swivel extension. The bolt is on the passenger side. Wanna help do head gaskets?
I cant turn the distributor counter clockwise to advance the timing it will not budgeEven with bolt blasterHow do you get it to turn1989 mustang lx?
Have you loosened the retaining bolt? That is the bolt that holds the distributor in place.
Which way does the distributor turn clockwise or counter clockwise on a 1993 ford aerostar?
There is no distributor, there is a sensor at the flywheel and the eng uses a coilpack. Doug C
How do you align a new torque converter on a 1993 Corolla to the drive plate?
It is easier to do if you install the torque convertor to the transmission and then attempt to bolt it to the flywheel. You will have to turn the convertor or flywheel to line up the bolt holes.
