0
Remove the air cap valve cover from the top right fork and by doing so the air pressure inside the fork will fall to zero. dump the pressure just like letting air out of a tire. Next, remove the hose between the front forks. At this point you can make things easier by placing a floor jack on wheels under the bike to lift the front wheel off the ground but loosen the main front fork caps before you jack the bike up. Jacking the bike up means less spring pressure inside the forks, so it will be easier to remove the caps. Now remove the fork caps from both forks but be careful as the spring may shoot out. Get a vessel to put under the forks and drain off all fluid. Lower the bike to floor or ground level. Restore drain plugs into their original position. Next, add 10.2oz of ATF brake fluid to each fork. Put the air caps on and tighten them well. Reinstall hose between front forks. Finally, you must pressurize the forks. Do this with an air pump such as is commonly found at gas stations or with a manual pump that has an air gauge. The correct pressure for each fork is 10-16 psi, according to how stiff you want the forks to be.
What else can I help you with?
How much Fork oil does a 1985 Honda cb650sc nighthawk take?
12.75 .oz #10 fork oil 6psi pressure
What is fork oil capacity on 1985 Honda cb450sc Nighthawk?
185cc or 2.26 fl oz As per clymer manual.
How much fork oil goes into the fork of a 1983 Honda CB650SC Nighthawk?
left 15.7 right 15.2, 0-10 psi
What is the fork oil capacity for a 1993 Honda CB 250 Nighthawk?
About 16 US fl oz.
What kind of fork oil does a 1984 Honda nighthawk 700 take and how much?
The 1984 Honda Nighthawk 700 typically uses 10W fork oil. The amount required for a complete fork service is approximately 11.5 ounces (about 340 ml) per fork leg. Always consult the owner's manual or a service manual for specific details and recommendations based on your maintenance needs.
What fork oil do you use for 1982 Honda cb450sc nighthawk?
I'm still looking for what kind of fork oil is available, but the manual says you can use Dexron ATF
Where is the VIN on a 1983 Honda Nighthawk?
Front left fork, right below turn signal. Should see model and Vin
What weight fork oil goes in a 1983 Honda nighthawk?
For a 1983 Honda Nighthawk, the recommended fork oil weight is typically 10W. However, it's important to consult the owner’s manual or a service manual for your specific model, as variations can occur based on factors like rider preference and modifications. Make sure to also consider the climate and riding conditions, as these can influence the choice of fork oil.
What is the fork oil capacity of a 1985 Honda Vt1100c shadow?
14 oz
How much fork oil does a 1984 Honda nighthawk 650 take?
The 1984 Honda Nighthawk 650 typically requires about 11.0 ounces (or approximately 325 milliliters) of fork oil per leg. It's important to use the recommended viscosity, usually 10W or 15W, depending on your riding preferences and conditions. Always check the owner's manual or service manual for specific details and recommendations for maintenance.
Fork oil capacity for a 1992 750 nighthawk?
472ml
How do you put fork oil in a 1982 750 Honda nighthawk?
To add fork oil to a 1982 Honda Nighthawk 750, first, ensure the motorcycle is on a stable stand and the front wheel is off the ground. Remove the fork caps using a socket wrench, then carefully pull out the fork tubes. Drain any old oil, and using a funnel, refill each fork tube with the appropriate type and amount of new fork oil, typically around 10-12 ounces depending on the model. Reassemble the forks by replacing the tubes and caps, ensuring everything is tightened securely before lowering the bike.
