0
You have to set the piston at Top Dead Center (TDC). I beleive the lash adjustment (valve clearance) is .004 to .006 in. That means thousandths. Once you have set piston at TDC (valve springs will not be compressed but extended on the compression stroke at TDC). You can now set the lash adjustment by loosening the set nut and bolt. You need a feeler gauge to do this. Set lash on both valves then recheck.
What else can I help you with?
How do you adjust valves on 17Hp Briggs and stratton ohv Family ybsxs.5012VP 274826?
You can adjust the valves on your 17 horsepower Briggs and Stratton engine by turning the adjustment screws. The adjustments screws will determine how much fuel goes into the piston chamber.
How do you adjust valves on a 19.5 Briggs and Stratton Its a 2006 or 2007 engine?
Try watching the video in the link below.
How do you adjust valves on a Briggs and stratton engin?
The valve clearance is set by grinding the faces if there is too much clearance or grinding the tip of the stem if there is too little. If it is a OHV engine you can easily adjust the valves. Try going to the link below for a video that shows how to adjust the valves.
How do you adjust valves on your Briggs and stratton lawnmower engine 18.0 ohv?
You do not state if it is a single or a twin (which it could be of either at that HP) so links to each below:
How do you adjust valves 21 hp Briggs stratton intek v twin?
Valves 21 hp Briggs and Stratton Intek V Twin can be adjusted by increasing the torque on screw band with a right rotation. This can eliminate some leaking problems.
Does a 14 hp Briggs Stratton engine on a riding lawn mower have overhead valves?
Yes They Do
How do you adjust valves on your 11 hp Briggs and stratton lawn mower engine?
If the valves are new you grind the end of the valve stem to the proper height . Otherwise you just clean the valves up real good and put them back in , there is no other adjustment .
How do you adjust the valves on a Murray riding mower with a Briggs and stratton 14.5 hp overhead valves?
This video will show you how: http://www.youtube.com/watch?v=NjzX-PUjKmo
How do you adjust valves on a 20 hp Briggs stratton?
To adjust the valves on a 20 hp Briggs & Stratton engine, first, ensure the engine is cool and disconnect the spark plug. Remove the valve cover, then rotate the engine to bring the piston to the top of the compression stroke, aligning the timing mark. Use a feeler gauge to measure the clearance between the rocker arm and the valve stem; it should be set according to the specifications in your engine's manual (usually around 0.004 to 0.006 inches for intake and exhaust). Adjust the clearance by turning the adjustment screw and then recheck the clearance before reassembling the valve cover.
What is valve clearance for Briggs and stratton 406777?
The valve clearance for a Briggs and Stratton 406777 engine is typically set to 0.004 to 0.006 inches for both the intake and exhaust valves when the engine is at top dead center on the compression stroke. It's important to adjust the clearance when the engine is cold to ensure accurate measurements. Always refer to the specific service manual for your engine model for the most precise information.
How do you adjust valves on 20hp Briggs and Stratton engine?
To adjust the valves on a 20hp Briggs and Stratton engine, first, ensure the engine is cool and disconnect the spark plug wire for safety. Remove the valve cover and rotate the engine to top dead center on the compression stroke. Check the clearance between the rocker arm and valve stem using a feeler gauge; it typically needs to be set to manufacturer specifications, often around 0.005 to 0.007 inches. Adjust the valve clearance by loosening the lock nut and turning the adjustment screw until the correct clearance is achieved, then re-tighten the nut and reassemble the engine.
How do you adjust the valves on a 15.5 Briggs?
To adjust the valves on a 15.5 Briggs & Stratton engine, first ensure the engine is cool and disconnect the spark plug for safety. Remove the valve cover to access the valves, then use a feeler gauge to measure the gap between the rocker arm and the valve stem. Adjust the gap as needed by loosening the lock nut and turning the adjustment screw until the correct clearance is achieved, typically around 0.003-0.005 inches for intake and exhaust. Reassemble the cover, reconnect the spark plug, and start the engine to check for proper operation.
