0
What else can I help you with?
Can you hook up two subs to a mono channel amp?
yes all u have to do is bridge them together
Bridge two subs to a four channel amp?
If you amp is bridgeable you run + sub wire to ch 1 + then the -sub wire to the - of ch 2 of the amp. The same with the other sub + ch3 - ch4 that's how to bridge your amp.
How do you bridge three subs to a two channel amp?
3 passive sub at 8 ohm imp in parralel will be 2.6+ impedence.Most of the professional sum amp can take up to 2 ohms load per channel(check the spec of the Amp)eg: you should be able to connect max 4 subs in each channel(match the watts pwr to amp)
How do you bridge a car amp and speakers?
To bridge your amp you have to first look at your amp,find the speaker hook ups and it should say either on the top or the bottom [-------------bridge------------------]- + - +- +- +- after you find this you will have to run two sub woofers or one duel voice coil speaker to the positive side and one to the negative side of the bridge on your amp,you will connect the two positives of the two subs together and hook up to the positive side of the bridge and then the two negatives of the subs together to the negative side of the bridge,that will bridge your amp and speakers.Make sure that your amp can handle the new load, if it can't ,then it will start to cycle on and off.If that happens just run in stereo,not bridge mode.(Some amps will have a switch that you have to press to make it run in bridge)
If you have two 900 watt RMS subs what size amp do you need to properly push them?
A 2 channel 900w per channel amp or less will run it, or a 1800w one channel amp etc.. Keep in mind the ohms need to match up too
Can you bridge two 1000 watt subs to a 2000 watt amp?
Yes, you can bridge two 1000-watt subs to a 2000-watt amplifier, provided the amplifier is designed for bridging and can handle the impedance load of the subs. Ensure that the combined impedance of the subs matches the amp's bridged output specification to avoid damaging the equipment. Additionally, verify that the subs are rated to handle the power output safely. Always consult the specific manuals for your equipment to confirm compatibility.
Can you hook both a subwoofer and speakers to 1 amp If so do I need to buy a amp that's even more powerful Then what the sub requires?
You can connect a sub and speakers to one amp, depending on how many channels your amp has. A 4 channel amp will be able to run one (or two) subs using two channels (one bridged* sub or two subs) and two speakers running one channel each. A 2 channel amp will run 2 speakers or one bridged sub. A 6 channel amp will run one bridged sub (or two subs), 2 front speakers and 2 rear speakers. In my opinion, you will get the most performance, depending on which amps you use, by using a monoblock amp for your sub and an amp with enough channels to run all of your speakers. # Bridged = putting together the power of two channels to run one sub or speaker. Note: not all amps are bridgeable.
How do you connect two amps to four subs?
Run a 2 sub per amp set-up. Get a distribution block for you power wire to split the power wire. You can run the remote wire from your stereo to one amp and then from the amp to the other amp. you will also need 2 sets of RCA's Easy way is too get a 4 channel amp to power 4 subs.
Is better to have a mono amp or 2 channel amp to 2 sub-woofers?
You won't notice any stereo separation with two subwoofers because our ears perceive bass as omnidirectional. Two subs can make more volume than one of the same size. If you are using two subs, you should either use two separate mono amps, or a two channel setup. As long as the amps have a high pass filter they will work equally well, although the wiring will be simpler for the two Chanel setup.
Im getting two 12 inch mtx terminator subs they can handle 1200 watts peak power 400 rms what amp should I get?
A 800 watt 2 channel amp will work
Is 4000 watt amp too much for two twelves subs?
Not if subs are rated for 2000 watts each.
Wire 2 dvc 4ohm subs to 2 channel Amp-sub400rms4ohm amp 350x24 ohm rms 700x22 ohm rms 1400x1 4 ohm peak power Best way to set up?
This question makes little sense. Could you say what model amp it is? With two 4 ohm subs, you can either do 1 ohm or 4 ohm. Now if you have a bridgeable two channel, I think you can do a 2 ohm load. For a 4 ohm load, two 4 ohm subs, connect both positives from one side of the subs to the positive out. Then the negative coils from the opposite side (other side of the sub) to the negative output. Then connect the remaining negative and positive together on each subs. Look here http://www.the12volt.com/caraudio/woofer_configurations.asp
