0
it's very easy only tools necessary is tools to undo bracket holder.
the fuel line has a u shape white plastic clamp on the fuel line, squeeze
the tabs together and push in on the clamp .(you can pull back from the back side)
to pull clamp back about half way and the fuel line will pull off filter.new filter comes with new clamps but i was able to use factory ones, i think they are better. the new filter does not come with end caps so if you have something to plug off filter when you pull the lines off it would be alot less messy since the fuel is going to flow out the filter.also make sure to wear eye protection.I did not have to release the line pressure since my car sat overnight, but did take off fuel cap. replace filer in bracket and push gas line back on push the plastic back down to hold gas line in place you should hear a clicking sound when snapped in place.after installing check for leaks.I don"t know procedure to release pressure from gas line.
What else can I help you with?
Does purolator oil filter fit 2005 mercury mariner?
Purolator builds a filter that will fit your Mercury. 4 cylinder uses the PL10241 V6 uses the PL24651
How many quarts of oil for Mercury Mariner 2009?
According to the 2009 Mercury Mariner Owner Guide : With engine oil filter change : The 2.5 liter four cylinder engine takes ( 5.3 U.S. quarts ) The 3.0 liter V6 engine ( 6.0 ) * 5W-20
What is the recommeded oil for 2007 mercury MARINER?
According to the 2007 Mercury Mariner Owner Guide ( 5W-20 ) -------------------------------------------------------------------- With engine oil filter change : The 2.3 liter four cylinder engine takes ( 4.5 U.S. quarts ) and the 3.0 liter V6 engine takes ( 6.0 )
How do you change cabin air filter on a 2007 mercury mariner?
Purchase a Purolator Cabin Filter. It comes with detailed instructions.
How many quarts of oil does a 2008 mercury mariner require?
According to the 2008 Mercury Mariner Owner Guide : With engine oil filter change : The 2.3L four cylinder takes ( 4.5 U.S. quarts of 5W-20 ) The 3.0L V6 ( 6.0 quarts of 5W-20 )
How many quarts of oil in a 2009 mercury mariner?
According to the 2009 Mercury Mariner Owner Guide : With engine oil filter change : The 2.5 liter four cylinder engine takes ( 5.3 U.S. quarts ) The 3.0 liter V6 engine takes ( 6.0 ) * 5W-20
How much oil is needed in a Mercury 2006 Mariner?
According to the 2006 Mercury Mariner Owner Guide : With engine oil filter change : The 2.3 liter four cylinder engine takes ( 4.5 U.S. quarts of 5W-20 ) The 3.0 liter V6 takes ( 6.0 of 5W-20 )
What oil filter do I need for a 2008 4 cylinder mercury mariner?
For a 2008 4-cylinder Mercury Mariner, you typically need an oil filter that meets the specifications for the 2.3L engine. A common option is the Motorcraft FL-910S or equivalent filters from brands like Fram or Purolator. Always double-check compatibility with your specific engine type and consult your vehicle's owner manual or a parts retailer for the most accurate recommendation.
Oil capacity for a 1999 mercury mariner 5.0 engine?
Answer oil capacity for mercury mountioneer with 4.6 v-8 with filter change ========================================================================= According to the 1999 Mercury MOUNTAINEER Owner Guide : With engine oil filter change : The 5.0L V8 engine takes ( 4.7 litres / 5.0 U.S. quarts of 5W-30 )
How do you change a transmission filter in a 2007 mercury mariner?
To change the transmission filter in a 2007 Mercury Mariner, first, ensure the vehicle is on a level surface and securely raise it using jack stands. Drain the transmission fluid by removing the pan bolts and carefully lowering the pan, then remove the old filter. Install the new filter, making sure it is properly seated, and clean the pan before reattaching it with a new gasket. Finally, refill the transmission with the appropriate fluid type and check the level as specified in the owner's manual.
How many quarts of oil in a 2007 mercury mariner?
According to our sources, oil, coolant and fuel capacity for this version of 2007 Mercury Mariner 4WD V-6 are as follows: Engine lubricant oil capacity: 5.7 liter / 6 U.S. qt / 5 imp. qt
How do you change transmission filter 2006 mercury mariner?
To change the transmission filter on a 2006 Mercury Mariner, first ensure the vehicle is on a level surface and the engine is off. Drain the transmission fluid by removing the transmission pan, then replace the old filter with a new one, ensuring the rubber gasket is in place. Reinstall the pan, tighten the bolts to the specified torque, and refill the transmission with new fluid as per the manufacturer's recommendations. Finally, start the engine and check for leaks, adding more fluid if necessary.
