answersLogoWhite

0

If you have a houseboat or an RV, the wiring is the same as a house. The black is the hot and it goes to the positive, the white is the neutral and goes to the negative. If you are not certain, contact the manufacturer of your watercraft.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

What two wires connect to the timer switch on a century 87423 battery charger?

The two wires which connect the timer switch on a Century 87423 battery charger are the red and black wires. The red goes to the positive connector while the black goes to the negative connector.


Connecting black and white wires to 306 angel eyes?

Just simply, connect all the black wires to the black wire coming out of the connector, and all the white wires to the white wire coming out of the connected. Use the blocks with screw in to connect them (pick them up from most car accessories shops like halfords, wilcos....etc).


What color wires should be used to connect an outlet: red, black, or white?

The white wire is typically used to connect an outlet.


What is the proper way to connect red, white, and black wires to an outlet?

To connect red, white, and black wires to an outlet, you should match the colors of the wires to the corresponding screws on the outlet. The black wire connects to the brass or black screw, the white wire connects to the silver or white screw, and the red wire connects to the brass or black screw. Make sure to tighten the screws securely to ensure a proper connection.


Outside porch lamp has no box just two wires coming in black wires are tied and don't connect to fixture just the white wires what is going on here?

You would have to provide more info to be certain what your problem is. Typically a black and white wire would connect to the two wires on the light fixture. The fixture should also be controlled by a switch that "breaks" the black (Hot Wire) to turn off the fixture. If you have a volt meter you can see if there is 120Volts between the black and white wires with switch on. If there is a single white wire going to fixture (Neutral), where is the "black wires tied" to. Maybe one of the black wires has broken off the fixture.


Can you run power from a light fixture to another light fixture?

Yes. Connect Black to Black, White to White and bare ground wires together.


How do you wire two outside light sensing motion porch lights that are controlled from one switch with each light having a white black ground and optional red wire?

Connect the black wire from the switch to the black wires of both lights. Connect the white wires together. Connect the red wire, if used for the motion sensor, to the black wires on the lights. Connect all ground wires together and to the ground terminal on the switch. Make sure to turn off power before connecting any wires for safety.


Where do you connect the negative battery cable wires?

At the battery if at all possible.


What is the proper way to connect white, black, and green wires in an electrical circuit?

To properly connect white, black, and green wires in an electrical circuit, you should match the white wire to the neutral terminal, the black wire to the hot terminal, and the green wire to the ground terminal. This ensures the safe and effective flow of electricity in the circuit.


How do you install 220 receptacle with white black and bare wires?

Assuming the wires are the correct gauge for application and breaker you use black and white wires as hot. Put red electrical tape on each end of white wire and connect red and black to the breaker output and bare wire to ground lug in panel. At receptacle connect black and red to hot contacts and bare wire to ground lug.


Where does the red wire in a baseboard heater connect to the black or white wire in the wall?

In the heater you will have two wires. You should then have 2 supply wires from the panel, and 2 wires from the thermostat. The neutral (white) supply wire should go to one of the wires on the heater. The hot (black) supply wire should connect to one wire from the thermostat. The other wire from the thermostat will connect to the other wire from the heater.


If the old block heater cord of a 1988 Honda CRX had two wires and the new end has 3 which colored wires connect the new connector to the old one?

Connect to two wires you have to the the spade connectors and forget the ground connector. The spade connector wires should be black and white. Black to gold and white to silver. If the wires coming from the heater happen to be red and white, then red goes to black. You could buy a simple lamp cord which has only tow wires.