0
What else can I help you with?
Why i haveNo sound after hooking aftermarket radio in 99 intrigue?
if you have the Bose system you might need to hook up the aftermarket amp wire to the factory amp
Can someone teach me where to connect my remote wire for my car stereo if i don t have a amp?
if you are talking about an aftermarket radio's amp turn on wire then without an amp you can just cap it off. if the harness used to connect to new radio to your factory wires has a blue antenna/factory amp then you can connect it to that provided the new radio doesnt have a second blue wire for that purpose.
Wiring aftermarket subwoffer to factory radio?
i can be done is you hav ethe AUX ports and some sort of remote wire to tell your amp to turn on while your radio is on.
When installing a new radio in a 1989 Dodge Caravan winfinity factory radio how do you integrate it with factory amp or bypass the amp?
if you are using an aftermarket wiring harness hook up the remote turn on wire on the new radio it should be blue with a white stripe to the harness also has a blue and white stripe and plug it in this wire turns on the factory amplifier if you are not using a harness you will have to locate the internal amplifier wire of the radio and connect that to the remote turn on on the aftermarket radio = answer = the inernal apm power wire is white on the black wire harness ANSWER if you dont want to use the factory amp. just run new speaker wires to each speaker.
You bought aftermarket radio and harness for a 91 explorer radio powers up but there is no sound why?
you have to power the remote wire, splice it into the power wire, it came with a factory amp. had the same problem.
How can you tell if a 1995 Ford Aerostar van has a factory amp?
The 1995 ford Aerostar did not come stock with a factory amp. If your van has an amp then it was added aftermarket.
What causes radio to cut out in 99 suburban radio has power no sound Ive tried a second known good radio any ideas?
I have a '95 Suburban and thought I had fried my aftermarket radio's internal amp, however after buying a new radio I still had the same problem. I then reinstalled the factory radio and the front and rear doors starting working again. A couple days later the rear doors starting working also. I then reinstalled my aftermarket radio and everything worked fine for a few weeks until one day I heard a pop and a fizz before all the stock speakers went out. Replaced the factory radio again until all the speakers worked, then installed the aftermarket. This time it only lasted a few days. Now only the fronts will play with the factory radio and none of the factory speakers function with the aftermarket. The problem is with the suburban's factory amps. My research has only came up with one amp for the 95 and prior suburbans and later models having two amps. Just like any other audio component, they go bad over time. It was too frustrating having to carry my factory radio just in case the factory amp fizzes out. I'm fed up and a factory replacement is nearly as much as an aftermarket. Therefore I am currently in the process of rewiring all of my speakers directly to an aftermarket multi-channel amp. Guess I'll upgrade the speakers while I'm in the process. Fix the problem for good and not have to worry anymore.
What is needed to play an aftermarket radio in a 95 Nissan 240 besides a radio harness mine had a factory clarion system in it with a built in amp?
The correct wiring harness should allow the radio to play. Make sure that the output of the radio is correctly wired to the amp (don't feed a high output speaker line into a low power amp input).
Why do would you bypass an amp?
Hi, If you are intending on bypassing the factory installed AMP you will have to connect the speaker wires directly to the stereo that you will be putting into the vehicle. However keep in mind that on some vehicles the AMP is connected secretly in the harness wires of the speakers and will not always work with an aftermarket radio....a good example are the stereos on Chrysler cars.
How to install an amp to a factory radio of a 2012 dodge ram 1500?
To install an amp to a factory radio of a 2012 Dodge Ram 1500, ensure that the amp bypass the harnesses.
Is it possible to replace the factory radio on a 94 Mark VIII with a JBL system and still utilize the factory amp and speakers?
I don't think that you can use the amp, plus you'd be changing it, they don't last long. All the speakers would have to be re wired. The original system worked well when it worked. I have changed the amp in my car about 5 times and the radio itself about 3 times. yes you can.. just make sure that the amp remote wire is hooked up from the radio to the harness Jeffa 989-Yes you can in fact use the existing factory amp with an aftermarket system and an aftermarket radio/cd/mp3 but the way I did it was through the wiring harness I picked up at an audio shop for around $20 which had all the correct plugs which you wire onto your aftermarket radio harness and run the amp from the rear of the head unit through rca cables white & red in color. you then need to be sure to wire the remote wire to a fuse that will only run when the car key is turned foraward to power the amp(s). When the car key is turned backward you should still be able to use the radio but without the extra power from the aftermarket amp. Just be sure that you've wired it up correctly and it should work for a good long time! If you are after alot of bass than adjust a little extra to the rear speakers which can handle a little more power and will prevent a blowout! Before I added the extra equipment I had to replace my factory installed jbl amp as I was able to locate one at a junkyard for $20 which wasn't bad. The radio powered but didn't power anything to the speakers. Good luck and contact me if you need additional information!
Can you install an amp on a factory radio of a 06 Impala?
yes
