0
How do you remove a spark plug when the wire came out the spark plug?
Wiki User
∙ 13y ago
If you mean that the wire came out of the boot, then pull the boot off of the spark plug and use a spark plug socket to remove the spark plug.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you change wire?
Spark Plug Wires? Remove them 1 at a time from the spark plug to the distributor or the ION pack, remove and replace the spark plug, add the new spark plug wire from the newly added spark plug to the distributor or ION pack.
How do you remove the spark plugs in a 88 Chevy Celebrity v6?
Remove the spark plug wire. Using a 5/8" spark plug socket with appropriate extension and driver unscrew the spark plug and remove it. The spark plug gap should be set to .045". Replace spark plug and reattach wire.
How do you remove spark plugs on boulevard cruiser?
Pop the hood open, remove the filter to the carburator, remove 1 spark plug wire boot at the front right side while facing the engine, remove the spark plug, add the new spark plug as well as the spark plug wire boot.
How do you change the spark plugs in a 1997 Toyota Tacoma?
You can change the spark plugs on the 1997 Toyota Tacoma yourself. Remove the ground wire and spark plug wire. Remove plug. Replace the plug with a plug made specially for your model car.
How do you remove a spark plug wire on a toro lawn mower?
how to replace plug wire on a toro mower
What should always be removed when working on a lawnmower?
Remove the spark plug wire from the spark plug and make sure it will not touch the spark plug. Or, you can remove the spark plug, but be sure and cover the hole so no debris will fall into the cylinder.
How do you check an engine for spark?
Remove the spark plug wire from the spark plug. Use some heavy gloves or a set of insulated pliers to hold the spark plug wire about 1/4-inch from the engine block (ground) and crank the engine - you should see a spark jump from the wire to the engine ground. For a better check, use another spark plug and put it on the spark plug wire and use it as a "jumper" from the wire to the engine ground.
How do you fix an engine with no compression?
To fix an engine with no compression first try replacing the spark plugs. Remove the spark plug wire and then remove the spark plug. Replace the plug with a new one. Reattach the wire. Replace all of your plugs and see if your engine will fire.
How do you replace spark plugs on 1999 Town and country?
Mark and remove plug wires. Remove spark plugs and install new plugs. Reattach plug wire to correct plug.
How do you know if im getting spark?
The easiest way to find out is to remove the wire from the spark plug and hold it about 1/4 inch from ground (the engine block is good) while someone cranks the engine in short bursts. If you are getting spark you should see a blue spark jump fromt the wire to the engine block. You might want to check all spark plug wires while you're at it. If you want to check the spark plug while you're at it, remove the spark plug and attach it to the end of the wire before checking for spark. If you get spark through wire but not through the spark plug, the spark plug is bad.
What does it mean if your car jumps after getting a tuneup?
Spark plug wire not connected to spark plug? Spark plug wire connected to Wrong spark plug? Vacuum line disconnected? Bad spark plug or wire?
Your 17 hp Briggs and stratten lawn mower won't start it has gas don't know if has spark?
You can check for spark by removing the plug wire from the spark plug and holding it about 1/4 inch from ground. Have some one crank the engine or pull the starter rope and look for a spark to jump from the spark plug wire to ground. DO NOT hold the wire with your bare hands since you will get shocked. If you have spark there, remove the spark plug and insert it into the end of the spark plug wire and do the same procedure. If there is no spark, the plug is bad. If you have spark, the problem lies elsewhwere.
