answersLogoWhite

0

there are 4 points holding the seat into the frame. i believe they are 10-14mm. just move seat forward to get the 2 rear bolts, then move it back to get to the 2 front ones. dont forget to disconnect the harness from the seat before you try to move the seat away from car.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How do you replace the water pump on a 1992 Nissan 300ZX?

first remove the fan and shrould. then the radiater and hoses. next remove the thermostat housing. remove the harmonic balancer(27mm or 1 1/16 shallow socket).remove all timing cover bolts(upper and lower). remove driver's side timing cover and move passenger side cover up just a bit to allow lower cover to be removed. a little tricky on the lower drivers side. may have to remove coolant temp sender and coolant temp sensor on the other pipe. no need to remove timing belt


How do you install a Mitsubishi eclipse driver mirror?

To install the Mitsubishi Eclipse driver mirror, you will need to remove the interior door panel on the driver's side. Then, remove the cover for the mirror screws. Remove the screws and wiring and remove the old mirror. Replace the wiring and screws as you add the new mirror to the car. Then place the cover and the door panel back on the vehicle.


How do you replace a fiat stilo driver side headlight?

To replace a Fiat Stilo driver side headlight , you need to first remove the battery cover and turn the steering wheel to the right. After this you should remove the wheel arch and then the cap that is on the headlamp back. This will make the bulbs visible. You can then proceed to replace the headlight.


How do you replace water pump on 1991 Nissan 300zx?

You must first remove the radiator then remove the timing belt cover. Keep in mind you'll need a 10mm socket/ wrench and a 6mm hex driver along with screw drivers. Taking the fan and fan cluth off the water pump has helped me in the past. You don't have to be under the car for this, I did this from above only.


How do you replace power steering pump Mazda 3?

first remove the front bar cover from driver side second remove the driver side head light,third undo the plastic cover under the driver side guard,fourth remove the windscreen washer bottle.now u can see the electric power steering pump just undo it.


How can you replace the air filter of a Kia Spectra 2000?

its on the right side when facing front[driver side] of the car behind the battery it will have a black cover and it has thick vent tube running to the engine remove the cover and replace


Replace cam angle sensor 300zx?

What year is it if its an 84-89 its located in the distributer. take off the dust cover just a couple of screws, then u will see 3 screws holding the sensor down remove those and pull the sensor out and replace.


How do you remove the cover and replace the overhead dome light on a 1994 Toyota Camry?

There is a small slot on the hard plastic cover near the end of the dome light you will need a small flat head screw driver insert the screw driver in that slot use a back and forth motion to remove it.


How do you replace the valve cover gasket on a 1987 Ford Crown Victoria?

Messy job, On the driver side you need to remove air intake assy and throttle assy to be able to remove the valve cover. On the passenger side, you have to remove the air intake plenum to get to the valve cover. Time consuming... but not impossible.


What is the process for led driver replacement in a lighting fixture?

To replace an LED driver in a lighting fixture, first, turn off the power supply to the fixture. Next, remove the cover of the fixture to access the driver. Disconnect the wires connecting the old driver to the fixture. Install the new driver by connecting the wires in the same way as the old driver. Finally, secure the new driver in place and replace the cover of the fixture. Turn the power back on to test the new driver.


Where is the fuse box on a 1985 300zx?

The fuse box on a 1985 Nissan 300ZX is typically located under the dashboard on the driver's side. You may need to remove a cover or panel to access it. Additionally, there is often a secondary fuse box located in the engine compartment. Always consult the owner's manual for specific details and diagrams.


How do you remove and replace the driver's side mirror on a 2002 Toyota Camry?

The small plastic cover in the corner of the window is removable. Mirror mounting fasteners and wiring connections can be removed to remove mirror.