0
What else can I help you with?
How much does it cost to replace throwout bearing on 93 Nissan 2wd truck?
The cost to replace a throwout bearing on a 1993 Nissan 2WD truck generally ranges from $300 to $600, depending on labor rates and whether you choose to use OEM or aftermarket parts. Labor costs can vary significantly based on location and the mechanic's expertise, as the job typically requires removing the transmission. Parts alone may cost between $50 to $150. It's advisable to get quotes from local mechanics for a more accurate estimate.
What rear end will fit 1997 geo tracker 2wd?
No
How do you replace front wheel bearing on 2005 Dakota 2WD?
To replace the front wheel bearing on a 2005 Dakota 2WD, start by safely lifting the vehicle and removing the front wheel. Next, remove the brake caliper and rotor to access the hub assembly. Disconnect the hub assembly from the steering knuckle by removing the necessary bolts and then carefully pull the hub out to replace the bearing. Finally, reassemble by reversing the disassembly steps, ensuring everything is torqued to the manufacturer's specifications.
Is there anything to align when replacing a clutch in a 98 Frontier 2wd or is it straight forward?
there is a tool that aligns the clutch disc with the pilot bushing to center it so that the input shaft will line up with the splines in the disc and pilot bushing. These are usually included with the kit which should include the tool, disc pressure plate, pilot bushing, throwout bearing, maybe spline grease. Also, lube the end of input shaft (go easy on the grease) and throwout bearing ball pivot and throwout bearing sleeve(what it rides on). Also when installing new bushing, don't use a punch to install or you will pean over edges and play hell getting input shaft in (use driver tool). Don't get any grease on the disc. Have flywheel resurfaced.
What could be causing your 97 Geo Tracker 2wd to have a high pitch grinding sound while driving in 1235 gear coming from the clutch area can also feel it in the shifter?
Your clutch throw-out bearing may need replaced.
Is it hard to replace a transmission in a 1990 Geo Tracker?
2wd-no its pretty easy 4wd- a little harder bc there is more parts and more to take off. o and if its a muanal its even easer
Can you grease front wheel bearing on 2003 Chevy silverado 2wd?
No it`s sealed unit
How do you replace the front wheel bearing on the driver side of a 2001 Dodge Ram 1500?
If you have 4wd the bearing is pressed onto to hub and can't be change. The unit is sold as a whole as a bearing hub. The cheapest I have found it was $171 at autozone. same is true for the 1500 2wd, only AutoZone doesn't have it listed! I had to get mine from the dealer. However, the dealer gave me a 8-lug hub instead of a 5-lug, but it had the same bearing.
How much does a 1993 Geo Tracker weigh?
HI, Here are 1993 Tracker weights 2,189 lb. 2WD Convertible 2,365 lb. 4WD Convertible 2,387 lb. 4WD Hardtop Steve H.
How do you replace a u- joint on a Ford Ranger?
how to replace u-joints on 1995 ford ranger 2wd
How do you know if the throw out bearing is bad on a 95 geo tracker If it is then what is involved in replacing it Do you have to drop the tranny clutch recently replaced not tob.?
if TOB screams when you press the clutch it is bad. if it collapes the clutch will be very hard to control. if it desecrates, no more clutch at all. no shifting. pull tranny , replace PP, disc, TOB and pilot bearing ALWAYS as a set. 5hours out and 5 in , max. i pull motor faster. do in 3out and in. record time. depends if car is 2wd , 4wd, (xfr case is extra work) but pulling engine makes the above line not true
2001 tacoma 2wd front wheel bearing torque?
For a 2001 Toyota Tacoma 2WD, the front wheel bearing nut should be torqued to approximately 140 ft-lbs (190 Nm). It's important to ensure that the wheel bearing is properly seated before applying this torque. Always consult the vehicle's service manual for the most accurate specifications and procedures.
