0
The crank sensor is located at the front of the engine (right side of the car) mounted slightly to the right of the belt pulleys. It sits just above the crankshaft. It is approximately 2 - 3/4 inches long and has two small cap screws, one on either side. Both can be accessed from the top without pulling the right front wheel.
Tools needed: 1/4 drive rachet and a 9/32 inch - 1/4 drive socket or 1/4 drive - 7 mm socket, 8 mm wrench and portable drop light.
Procedure:
1. Use 8 mm wrench to disconnect positive battery terminal.
2. Press in clip on pigtail and remove connector from top of sensor
3. Remove cap screws with rachet and socket.
4. Put a drop of Loctite medium strength on both cap screws.
5. Install new sensor (be careful to seat guide ring on back of top mounting hole into seat around bolt hole - when you start the cap screw it should set in place with no problem)
6. Install bottom screw and snug both.
7. Optional (use feeler gauge and check clearance between sensor tip and crank trigger. Clearance should be around .035 -.040 in.)
8. Tighten both cap screws - be careful not to overtighten. These are small bolts, easy to wring off.
9. Reconnect battery terminals.
10. Crank engine - done.
Hope this helps.
Jim B.
Jim@business-money-source.com
"Your One Stop Business Money Information Source"
www.Business-money-Source.com
What else can I help you with?
Where is the crank shaft sensor on a 1998 BMW 740il?
The crank shaft sensor on a 1998 BMW 74Oil is located down near the crank on the front of a motor. It is super easy to replace but sometimes reaching the harness wire is a little bit difficult.
Where is the crank sensor located on 1998 Bravada?
the crank sensor is located just behind the crank shaft pully of the engine.
1998 Oldsmobile 88. has no spark replace the igniton control module. what else could it be?
crank or cam sensor...did you already figure it out?
1998 Ford Taurus engine coolant temperature sensor- low input location?
where is the engine coolant temperature sensor- low input locationon a 1998 ford taurus
Is the crank sensor the same as the cam sensor on a 1998 ford escort wagon?
No
Where is the crankshaft position sensor located on a 1998 Mitsubishi Eclipse?
Crank position sensor is located next to the crankshaft. In order to replace it you might have to remove the timing belt. In the most models you just can remove remove the timing belt cover and replace the sensor.
What does a crank shaft sensor do on a 1998 Honda accord?
A crank shaft position sensor on a 1998 Honda Accord reads whether or not a the engine is spinning correctly. If there is a discrepancy on how the crankshaft is spinning the sensor will relay it to the ECU.
Where is the 1998 Taurus pressure switch?
1998 Taurus pressure sensor location; It is located on the firewall side between the head and the transaxile housing.
Where is the camshaft position sensor located on a 1998 ford taurus 6 cylander dohc?
The camshaft position sensor is located beneath the wheel on a 1998 Ford Taurus 6 cylander Dohc.
If the crank position sensor 1998 Dodge Dakota magnun v6 is not work what would happen?
If the crank sensor is not working, the engine will not run.
What would cause a 1998 Cherokee to stall while driving and not start not even push starting it?
Check the crank angle sensor usually about $150 to replace
Where is the crank sensor located on a 1998 Mitsubishi 3000 gt?
there is no crank sensor on a Mitsubishi 3000 gt but there is a crank angle sensor that looks just like a distributor its in the back of the engine on top between valve covers
