0
This is an easy task but it can seem confusing since you do not have a key to turn, like on other models. As you know, when you start your RAV4 with a smart key, you have to step on the brake pedal when you press the start/stop button before it will crank. To reset or clear the maintenance light, you will NOT put your foot on the brake pedal when you press the start/stop button. So, with foot OFF the brake pedal, press the start/stop button, you may have to press it twice to get the dash lights to come on, then set the trip button for the odometer to TRIP A mode. (NOTE: you do not have to hold the start/stop button, just press and release it.) Now press the start/stop button again to turn off the dash lights after you have placed the odometer to TRIP A mode. Next you will press the trip button and HOLD IT IN and then press the start/stop button to turn the dash lights back on. You will see the odometer display flashing dashes, just keep holding the trip button until you see 00000 and then it goes back to normal readings and the maintenance light is off. That's it. Hope this helps.
What else can I help you with?
How do you reset the maintenance reqired light in the 2011 smart key Toyota RAV4?
How do you reset the maintenance required light in the 2011Toyota RAV4 with a smart key starting system
How do you reset maintenance light on acura tl 2011?
To reset the maintenance light on a 2011 Acura TL, turn the ignition to the "ON" position without starting the engine. Press the "Menu" button on the dashboard, navigate to "Vehicle Settings," and select "Maintenance Info." From there, choose "Reset" for the maintenance reminder you wish to clear. Finally, confirm the reset, and the maintenance light should turn off.
How do you reset the maintenance required light on a 2011 Honda Accord -?
With the engine and ignition off push and hold in the odometer reset button. While holding that button in, turn on the ignition but do not start the engine. After about 5 seconds the light will go off and the maintenance required light will have been reset.
How do you reset the oil light on a 2011 Toyota Sienna le?
Set it to trip A and hold reset turn ignition off then turn ignition on and maintenance light will flash and your done.
How do you reset the maintenance required light on a 2011 Toyota RAV4?
You will need to take it into a mechanic. They will be able to check out your vehicle and then they can turn off the light.
How do reset maintenance light on 2011 Acura MDX?
To reset the maintenance light on a 2011 Acura MDX, first turn the ignition to the "ON" position without starting the engine. Then, press the "Select/Reset" knob on the dashboard until the oil life indicator appears. Press and hold the knob for about 10 seconds until the oil life resets to 100%. Finally, turn off the ignition to complete the process.
How do you reset the maintenance required light on 2011 Toyota Camry?
Turn key off. Push mileage reset button. Keep it pushed in while you turn ignition key to on position. Hold for 10 secs...
How to reset the maintenance required indicator light on a 2011 Toyota Corolla?
Turn the ignition key partially change display to "Trip A" and turn ignition OFF. Press the trip reset button and then turn the ignition key partially. Do not start engine. Hold reset button down until light goes off.
How do you reset oil light after oil change in 2011 FORD E350?
It is very easy to reset the oil light after you had an oil change in your 2011 Ford E350. You will just need to disconnect the battery for up to 1 minute to reset the light.
How do you reset the oil light on a 2011 Nissan Altima?
Two buttons on the left side of the steering wheel on the dash, square and circle marks. Press the square one go to maintenance, oil, reset; select using the other button.
How do you turn your maintenance required off for your 2011 Toyota corolla?
To turn off the maintenance required light on a 2011 Toyota Corolla, first, turn the ignition to the "On" position but do not start the engine. Next, press the gas pedal three times within five seconds. Finally, turn off the ignition, then start the engine to ensure the light has reset. If the light remains on, you may need to repeat the process.
How do you reset the change oil light on a 2011 explorer?
asy
