answersLogoWhite

0

You will need to pull the negative lead from the battery for 10 minutes.

Or you can just wait for a couple of days and it will reset on it's own, as long as you fixed the reason for it lighting in the first place.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How to reset check engine light 1991 Toyota land cruiser?

try disconecting the battery or pulling the ECM fuse


How do you reset the check engine light on a 2007 Chrysler PT Cruiser?

You use a scan tool after repairing the cause of the code.


How do you reset the 'check engine' light on a 2002 pt cruiser yourself?

To reset the 'check engine' light on a 2002 PT Cruiser, you can disconnect the negative battery terminal for about 15 minutes. This will reset the vehicle's computer and clear the light. Alternatively, you can use an OBD-II scanner to read and erase the trouble codes. However, it's important to address any underlying issues that triggered the light before resetting it.


How do you reset the check engine light on a 2006 Chrysler PT Cruiser?

You use a scan tool after repairing the failure that caused the code.


How do you reset check engine light after replacing O2 sensor on 2004 pt cruiser?

Just unplug the negative terminal of the battery for about 10 minutes and that will reset the computer


Reset check engine 2008 fj cruiser?

To reset the check engine light on a 2008 FJ Cruiser, you can start by disconnecting the negative battery terminal for about 10-15 minutes. This will clear the engine codes stored in the vehicle’s computer. Alternatively, you can use an OBD-II scanner to read and clear the codes directly. However, be sure to address any underlying issues that triggered the check engine light before resetting it.


How do you reset the check engine light on a 2003 Chrysler PT Cruiser?

You can unhook the battery or use a scan tool to erase the code. If the cause is not repaired, the light will return.


How do you reset the check engine light on a 2008 Chrysler Sebring?

The check engine light is reset with a scan tool after repairing the cause of the fault.The check engine light is reset with a scan tool after repairing the cause of the fault.


How do you reset the check engine light on a 1999 volkswagen jetta?

The check engine light has to be reset with a OBD scan tool


How do you reset the check engine light on 2007 dodge with cummins engine?

You reset the check engine light with a scan tool after repairing the failure.


How do you reset timing belt light on Toyota Land Cruiser?

To reset the timing belt light on a Toyota Land Cruiser, first turn the ignition key to the "ON" position without starting the engine. Press the gas pedal three times within five seconds. Turn the ignition off, then start the engine to check if the light has been reset. If the light remains on, you may need to consult the owner's manual or a professional for further assistance.


How do you reset the check engine light in a land rover discovery?

hoe do you reset the check engine light in a 1995 land rover

Trending Questions
How many cold cranking amps on your battery do you need for a 1992 Ford F-250 with the 4.9L I6 engine? What temperature can be expected on the surface of the catalytic converter? How do you remove a rear drive shaft? What do you do if a lot of white smoke is coming out of the muffler? Fuel pump relay location on 2000 S-10? What is the gap in a spark plug for Volvo v70 1999? Car makes loud knocking sound at high speeds? What was used before PCV valves? What component transfers drive from the transfer case to the front and rear axle assemblies in a conventional 4wd vehicle? How do you put a balance shaft belt on a Mitsubishi mighty max? How are tires rotated? A parking brake system is not required if your service brakes are fully? What is the meaning of the mt90b16 in tire size? Why are you beams used as a support opposed to solid rectangular beams? How do you install the serpentine belt on a 2000 ford ranger 3.0? What does orange light mean on fiesta 2000 looks like a person wearing a seatbelt? Where can a person find a wiring diagram for a 1990 Dodge D250 diesel pickup as the tailights and dashlights don't work? 2000 gmc jimmy ball joint what kind of noise will it make when going bad I have a very slite clunk or popping noise when stopped and i turn the wheel to the left. i have greased them every 3000 mi? How do you replace the brake calipers and how do you remove the clamp on the hose connected to the caliper on a 2000 Chevrolet Malibu? What is the fuel pump pressure for a 1991 Pontiac firefly 3 cylinder?