== == This also applies to the 2001 GMC Jimmy.
The headlight assembly is held in place as one entire unit.
In between the battery and the headlight assembly unit are two tabs that when pulled upward (by hand) will release the housing from the vehicle. (VERY EASY once you know).
The headlight assembly is now held to the vehicle ONLY by wires, so don't let it drop and break. It's now just a matter of bulb replacement from the backside of the headlight assembly. Do this by turning the bulb in it's socket until the little catches line up with the open slots and poll the light bulb out. Do NOT touch the glass portion of the new bulb you are installing if it is a halogen bulb. Doing so will severely shorten the life of the bulb since contaminants on your hands cause the bulb to quickly overheat and die.
Once the bulb is changed and plugged back into the wires, put the headlight assembly back in place by aligning it and poke the two plastic pegs on the back of the headlight assembly into the two square holes in the front of the vehicle. Now slide the two tabs you originally pulled up to release the headlight assembly, back down into place making sure the "slots" at the bottom of sliding tabs catch the square plastic pegs on the back of the headlight assembly.
Do NOT pound the sliding tabs back down. Doing so will break the square pegs off of the back of the headlight assembly and pounding is not necessary if you have them properly in the square holes and all of the way in. Thank you to whoever first wrote this answer and to WIKI for making it available.
Remove the wiring harness from your 2000 Kia headlight. Remove the headlight assembly retaining bolts. Reverse the process to install your new headlight assembly.
The headlight assembly on a 2000 Acura Integra is held on using bracket bolts. Prop the hood open and locate the headlights. Unbolt the brackets and remove them. Carefully pry the headlight assembly out to not harm the weatherstripping.
To replace the headlight on a 2000 Jaguar XJ8, first, open the hood and locate the headlight assembly. Remove the retaining screws or clips securing the assembly, then gently pull it out. Disconnect the electrical connector from the back of the headlight bulb, replace the bulb, and reconnect the connector. Finally, reinsert the headlight assembly and secure it with the screws or clips.
To remove the headlight from a 2000 Honda Civic, first, open the hood and locate the headlight assembly. Remove the screws or bolts securing the headlight, typically found on the top and side of the assembly. Disconnect the wiring harness by pressing the tab and pulling it out. Finally, gently pull the headlight assembly out of the socket to complete the removal.
go to back of headlight assembly and twist it out.
open the hood. in back of headlight assembly there are two metal slides with pull tabs. pull them up then wiggle the headlight assembly. it should fall right out. with it out you can get at the bulbs.
To remove the headlight assembly on a 2000 Dodge Caravan, first, open the hood and locate the retaining screws or bolts securing the headlight assembly. Typically, you will need to remove a few screws from the top and possibly a clip from the side. Once the screws are removed, gently pull the headlight assembly forward to disconnect it from the car, and carefully unplug the electrical connector. After that, you can replace or service the assembly as needed.
To replace the headlight assembly on a 2000 Pontiac Grand Am, first, remove the screws and clips securing the assembly to the vehicle. Disconnect the electrical connector from the back of the headlight and carefully pull the assembly out. Install the new assembly by connecting the electrical connector and securing it with the screws and clips. Finally, test the headlights to ensure they're functioning properly.
No. It secures the headlight assembly in place. The headlight adjustments are the square slot crews that have a spring assembly around them.
To change the headlight assembly on a 2000 Nissan Xterra, first, disconnect the negative battery cable to ensure safety. Remove the screws or bolts securing the headlight assembly, typically found around the perimeter, and gently pull the assembly forward. Disconnect the wiring harness from the back of the assembly, then replace it with the new assembly by reversing the steps, ensuring all connections are secure before reconnecting the battery. Finally, test the new headlight to ensure it functions properly.
on top of headlight assembly, there are 2 tabs to pull up, then pull assembly out.
To replace the headlight on a 2000 Chevy Metro, first, open the hood and locate the headlight assembly. Remove the retaining screws or clips securing the assembly, then gently pull it forward. Disconnect the wiring harness from the back of the headlight bulb, replace the bulb with a new one, and reassemble the assembly by reconnecting it and securing the screws or clips. Finally, test the new headlight to ensure it works properly.