0
What else can I help you with?
What does the term dual voice coil mean in regards to car audio speakers?
AnswerDual Voice Coil in regards to subwoofers means there is 2 positives and 2 negatives. Its just used to wire up different ohm levels. Like if u have a subwoofer that are dual voice coil @ 4 ohms then u can parallel or series wire it to become Single Voice Coil @ 2 ohms. Google the word Series Wiring or Parallel Wiring for examplesAlso this type of speaker is one of the few that can be connected to 2 different amplifiers at the same time and still work properly. One coil is connected to the car stereo and the other coil is connecter to my scanner.
How do you wire amp to 1 ohm load?
need more info but I'll give it a shot and hope i answer your question. You will need one of the following to get your desired ohm load: 1- single voice coil at 1 ohms 2 - single voice coil at 2 ohms wired + to +, - to - 2 - dual voice coil at 4 ohm all wired + to +, - to - so that you only have 2 wires conected to the amp. hope this helps.
How do you wire dual voice coil 4ohm?
you don't light the car on fire and make it explode
Can you replace a dual voice coil speaker with a single coil and how do you wire it?
If you are going to replace a dual with a single you need to look up bridging it would be some thing like "{Right +}{Left -}
How do you wire up a dual 4 ohm sub to 2 ohms?
i dont now
How many ohms on a 1999 Yamaha banshee coil?
Primary (Black and Orange wires) 0.28 to 0.38 Ohms (almost a short). Secondary (Spark plug wire to spark plug wire) 4700 to 7100 Ohms.
Would running two 4 Ohm dual voice coil subwoofers add to 16 Ohms?
There are many different ways that you could wire two dual voice coil subwoofers. Depending on how you connect the voice coils, you could have 1ohm (all coils in parallel), 4ohms (parallel-series combination). Technically you could wire them for 16ohms (all in series), but this isn't done in practice because an amplifier won't provide much power to a 16ohm load. You should wire the subwoofers to make an impedance (which is the 'ohms') which will match your amplifier. Not all amplifiers can handle 1ohm, so you may need to wire the subwoofers for 4ohms. Be sure to do some research on this before wiring anything up or you could damage your amplifier. For some helpful wiring diagrams, check out the Fosgate Wiring Wizard: http://www.rockfordfosgate.com/rftech/woofer_wizard.asp?submitted=true&woofer_qty=2&woofer_imp=4
Will a 540 Watts x 1 RMS 4ohms Amplifier be suitable for a sub rated at 380 watt RMS with 4ohms plus 4ohms dual coil?
The problem you have there is that your sub woofer needs both coils wired and your options with that setup is either 2 ohms or 8 ohms depending on if you wire the sub itself in series or parallel. If you use a second sub like the first one and wire both subs in parallel and then wire the two subs in series you can achieve 4 ohms. You could also wire the subs in series ( 8 ohms each ) and then wire them in parallel to achieve the overall 4 ohms.
How do you wire monoblock amp to one single voice coil sub?
Unless you have some kind of different set up or amp, a monoblock amp should have just 2 terminals. A positive and a negative. Your single voice coil should also only have 2 terminals, a positive and a negative. If this is your setup, just connect positive to positive and negative to negative. It's that simple. If you have a dual voice coil there is more involved regarding ohms (resistance) but in a mono to single v/c, it's pretty straight forward. You might also check the amps on the monoblock vs the speaker. Your monoblock will probably be either 2 or 4 ohms. Your speaker could be 2, 4 or 8. If your speaker is 4 ohms then a 2 or 4 ohm output from the monoblock will work. If you have any other combination, do more research.
Can a lawn mower coil be tested with an ohmeter?
Yes. Try it sometime - you might like it. The spark plug wire contact should read high ohms to ground. The coil should read much lower ohms to ground.
When connecting a dual voice coil subwoofer to a mono amp what is the best way to connect the subwoofer to the amplifier?
To connect a dual voice coil subwoofer to a mono amplifier, the best method is to wire the voice coils in parallel if the amplifier supports the resulting impedance. This configuration will lower the overall impedance, allowing the amp to deliver more power to the subwoofer. If the amp cannot handle the lower impedance, you can wire the coils in series, which will increase the impedance but reduce the power output. Always check the specifications of both the subwoofer and amplifier to ensure compatibility.
What next for a 98 deville northstar 3 cylinder misfiring changed plug coil wire and injector reads 12.6 ohms could injector still be bad?
Need to check the coil wire, and all other ignition parts.
