0
Gravity bleeding is, in theory, a method of removing air from hydraulic passages (flex hoses, steel lines, etc) by using gravity to push fluid downward through these passages.
Hydraulic clutch systems can be gravity bled by loosening the bleeder screw at the slave cylinder and allowing the fluid to drain (into a container), making sure to keep the fluid level in the reservoir at least half full. Once the fluid is draining consistently, tighten the bleeder screw and top off the reservoir. It is very important that the reservoir does not go dry, so keep an eye on the fluid level.
ANSWER
LOOSEN WHEWHERE THE BLEEDER ON THE SLAVE CYLINDER LET IT DRIP UNTIL NO BUBBLES, DOUBLE OR TRIPPLE FLUID LOSS THE SIZE OF YOUR RESERVOIR JUST TO MAKE SURE,ITS BETTER YOUR SAVING BOTH PUMPS THAT WAY OR VACUUM BLEEDER HAND PUMPS LIKE DEALER JOBS CLUTCH FEEL,THE MAIN JOB IS NO LEAKS ON THEM FLUID PIPES EITHER WAY THEY SHOULD BOTH WORKS OK,HOPE THIS HELPS
What else can I help you with?
Do you need to bleed the clutch after new install?
yes, u need to use the bleeder valve or u can gravity bleed it
How do you bleed the clutch on a 99 Saturn SL1?
bleed clutch Saturn vue 2003
How do you bleed the clutch in a 95 Daewoo cielo?
there dry clutch's, run a cable. no fluid. .:. you can't bleed it. :)
How do you gravity bleed clutch master cylinder?
This is goo video that demonstrates gravity bleeding very well it is very stait forward and easy, just imagine the bell housing around the clutch to get a feel of were the bleeder screw is. http://www.youtube.com/watch?v=HgNTDGwcjZc
How do you bleed the clutch line on a 2004 ford ranger edge?
how do I bleed the clutch system in a 2004 ford ranger
When do you bleed your clutch?
after the clutch master cylinder has been replaced.
Where and how do you adjust the clutch on a 94 escort?
The clutch can't be adjusted. It is an hydraulic clutch. The clutch pedal sends pressure from the master cylinder to the slave cylinder on the clutch. IF you are having trouble with it the thing to do is bleed the air out at the slave cylinder. Have an assistant pump the clutch and hold it to the floor. Then open the bleed valve on the slave cylinder to let the air out of the system. On the final bleed hold the clutch to the floor and close the bleed valve on the slave cylinder. The clutch master cylinder operates of the brake fluid reservoir. Make sure you keep this full of brake fluid as you bleed the clutch.
How do you bleed a clutch on a Nissan stanza?
To bleed a clutch on a Nissan Stanza, you need to find the bleed-off valve, usually somewhere near the slave cylinder.
How do you bleed the clutch on a 1998 Mercury Cougar RHD?
Fill resevoir open bleeder valve at slave cylinder Gravity will cause fluid to run out Depress clutch pedal and hold Tighten bleeder screw
How do you bleed a hydraulic clutch system on a gmc sierra?
shhould be da same way u bleed your break system... bleed valve on clutch master cylinder...
How do you bleed the clutch. 2003 Mitsubishi lancer?
same way you bleed the brakes. push clutch all the way to the floor and release the bleed valve on the transmission. tighten it up, release the clutch. Need 2 people to do it.
How do you bleed the clutch on 1997 Pontiac Grand Am?
Loosen the bleed screw next to the entry point on the transmission, open the clutch master cylinder (drivers' side rear corner of the engine bay), and let it bleed. It's helpful to use a hose over the bleed screw that goes into a bottle so you can watch for bubbles. Keep an eye on the fluid level as it should drop fast. Don't pump the clutch or hold it down. The bleeding is supposed to just happen with gravity. Good luck
