0
You can turn the light off a couple of ways, if you want it off for a short time like enough time to get an emissions done, just disconnect the battery for a couple of minutes. This will only work for a while though, after the computer receives the fault codes from the sensors it will cut back on. The very best way is to just find out why its on and break down and repair the problem. This is the only sure way to get it off. The final and cheapest way...Black electrical tape over the light -Wcb56
What else can I help you with?
What is a fuel pressure check valve and where it is located in 92 Cadillac brougham with 5.7 L engine?
Look for a bicycle tire fill tube and tire ca.
Why is my Cadillac Escalade check engine light on?
Yea my cadillac light check engine whay
How do you add antifreeze to a 1990 Cadillac brougham?
To add antifreeze to a 1990 Cadillac Brougham, first ensure the engine is cool and then locate the coolant reservoir, which is typically near the front of the engine bay. Remove the cap, and if necessary, add a 50/50 mixture of antifreeze and distilled water until the level reaches the appropriate mark. Be cautious not to overfill, and check for any leaks after adding the antifreeze. Finally, replace the cap securely before starting the engine.
Cruise control inop on a 1984 Cadillac Fleetwood brougham?
check fuses and for vac leak at unit and vac pump
Why does the check engine light on a 1994 Cadillac Fleetwood come on?
it could be so many diffrent things google "error codes for a 1994 fleetwood brougham" it will send you to myweb.accesuss.com or .net..very usefull in tracking down the cause
Find picture of a Cadillac brougham 307 motor?
I can't provide images directly, but you can easily find pictures of a Cadillac Brougham with a 307 motor by searching online through platforms like Google Images or automotive enthusiast websites. Simply type in "Cadillac Brougham 307 motor" in the search bar, and you'll find various images showcasing the motor and the vehicle. Additionally, you might check classic car forums or Cadillac-specific communities for more detailed visuals and information.
Why no power to my stereo in cadillac 1987 brougham?
its probably the fuse for the cigg lighter. Check that right under the steering column. It should be marked.
Is there any fuses for the fuel pump on a 1991 Cadillac Brougham?
Yes, the 1991 Cadillac Brougham has a fuse that protects the fuel pump circuit. This fuse is typically located in the fuse box under the dashboard or in the engine compartment. If you're experiencing fuel pump issues, it's a good idea to check this fuse along with the relay to ensure they are functioning properly. Always consult the owner's manual for the exact fuse location and specifications.
How do you install air compressor belt on a 1988 Cadillac Brougham?
To install the air compressor belt on a 1988 Cadillac Brougham, first ensure the engine is off and cool. Loosen the tensioner pulley by turning the adjusting bolt, which will allow you to remove the old belt. Route the new belt around the air compressor pulley and any other pulleys according to the belt routing diagram, then tighten the tensioner back to maintain proper tension on the belt. Finally, double-check the alignment and tension before starting the engine.
Is your water pump going in your 1989 Cadillac brougham?
To determine if the water pump in your 1989 Cadillac Brougham is failing, listen for unusual noises like grinding or whining, check for coolant leaks under the vehicle, and monitor the engine temperature for overheating. If you notice any of these symptoms, it could indicate a problem with the water pump. Additionally, inspect the pump for any visible signs of wear or damage. If you're uncertain, consulting a mechanic for a professional assessment is recommended.
How do you turnoff check engine light Honda Odyssey?
First have the problem that turned the light on repaired. Then use an OBD2 scan tool to reset the light.
What are the procedures for timing a 1993 Cadillac brougham with a 5.7liter TBI?
To time a 1993 Cadillac Brougham with a 5.7-liter TBI engine, first, ensure the engine is at operating temperature. Disconnect the timing connector (usually a tan wire with a black stripe) to set the timing control to the base timing mode. Use a timing light to check the timing marks on the harmonic balancer, adjusting the distributor as necessary to achieve the specified timing of 0 degrees BTDC. After adjustment, reconnect the timing connector and recheck the timing to ensure it remains correct.
