answersLogoWhite

0

If you disconnect the TPS sensor, there would be hesitation on acceleration.

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

How do you check a throttle position sensor?

To check a throttle position sensor (TPS), first, ensure the vehicle is turned off and safely secured. Disconnect the TPS connector and use a multimeter to measure the sensor's resistance or voltage output while manually moving the throttle plate. A functioning TPS should show a smooth and consistent change in voltage as the throttle opens and closes. If there are abrupt changes or no response, the sensor may be faulty and should be replaced.


How to clean a tps?

To clean a throttle position sensor (TPS), first, disconnect the battery to prevent electrical issues. Remove the TPS from the throttle body, then use a spray cleaner specifically designed for electronic components to gently clean the sensor and its connectors. Avoid using abrasive materials that could damage the sensor. Reinstall the TPS, reconnect the battery, and ensure everything is functioning properly.


How do you replace the throttle position sensor in a 1993 subaru impreza?

To replace the throttle position sensor (TPS) in a 1993 Subaru Impreza, first disconnect the negative battery cable to ensure safety. Locate the TPS on the throttle body, disconnect the electrical connector, and remove the two screws securing the sensor. Install the new TPS by aligning it properly, securing it with the screws, and reconnecting the electrical connector. Finally, reconnect the battery and check for proper operation.


What would cause a 91 Honda CRX HF to rev up and down?

air leak in the throttle or intake manifold gaskets or bad TPS sensor, disconnect TPS as a temporary fix


Tps sensor 1996 ford Windstar what does it do?

TPS IS THROTTLE POSITION SENSOR


How do you test a TPS on a 1991 S10?

To test the throttle position sensor (TPS) on a 1991 Chevy S10, you'll need a multimeter. First, locate the TPS on the throttle body and disconnect the electrical connector. With the multimeter set to measure voltage, probe the middle terminal of the TPS while slowly moving the throttle from closed to wide open; you should see a smooth increase in voltage. If the voltage is erratic or doesn't change appropriately, the TPS may be faulty and should be replaced.


Directions o how to Replace a TPS Sensor on a 99 S10 Pickup PLEASE?

The 1999 General Motors (GM) Blazer/Jimmy came offered in the optional 4.3L Vortec V6. The throttle position sensor (TPS) is easy to remove as it is two mounting screws and one quick disconnect wiring harness attached to the throttle body. The OEM GM AC Delco replacement TPS should be #2134668 and or #213912.


How do you replace throttle position sensor in 1999 Nissan maxima And where is located?

Disconnect the negative battery cableRemove the air intake duct and disconnect the TPS and wide open/closed throttle switch electrical connectorsRemove the two retaining screws and separate the TPS from the throttle body


How do you change throttle position sensor on 1995 Lincoln mark VIII?

To change the throttle position sensor (TPS) on a 1995 Lincoln Mark VIII, first disconnect the negative battery cable to ensure safety. Locate the TPS, which is mounted on the throttle body, and unplug the electrical connector. Remove the two screws securing the TPS, replace it with a new sensor, and reattach the screws and connector. Finally, reconnect the battery cable and check the sensor's functionality.


Where is the throttle position sensor located on a 1987 Pontiac grand am 2.5l?

It is located on the passenger side of the throttle body.Remove the air cleaner housing, and stand on the passenger side of the car. The throttle position sensor (TPS) is on the side of the throttle body, behind several plastic vacuum lines. Disconnect the brackets that hold the lines to access the two bolts that secure the TPS. These are Torx 25 bolts, so be sure to use the right driver. Disconnect the electrical connection (you may have to disconnect others to gain access) and remove the TPS. The new TPS may have to be angled in to get the tang from the throttle to line up with the guides in the new TPS. Good luck with the operation, as there is not much area to work.


How do you install the throttle position sensor on a 1987 Pontiac fiero?

To install the throttle position sensor (TPS) on a 1987 Pontiac Fiero, first disconnect the negative battery terminal to ensure safety. Remove the electrical connector from the old TPS, then unscrew the sensor from the throttle body. Position the new TPS in place, aligning it properly, and secure it with screws. Finally, reconnect the electrical connector and the battery terminal, then check for proper operation.


When the tps sensor is disconnected from the car in idle what happens?

When the TPS sensor is disconnected from the car in idle, there would be delayed acceleration.