0
If you have a 1000 watt 2 ch amp and 2 1000 watt G A 12's how do you set it to 1 ohm?
unfortionatly it alot more difficult than that. you first need to know if your subs are dual or single voice coil. then the ohm of the coils. your next step is to make SURE your amp is one ohm stable. (most are not) if your sub ohm will match you amp ohm. safely. its all in the wireing of the amp to the subs to change the ohms. if you dont know exactly how to wire them DONT DO IT yourself.
What else can I help you with?
Dose a 1000 watt 1 ohm stable amp work for my dual 2 ohm L7 12s?
yes but make sure the rms power for each is the same or close at 2 ohms and wire both subs in series-parallel
What size amp do i need for two 10 inch kicker comp's?
You could go with a 600 watt 2 ch amp or a 300 watt mono block amp, depends on what OHM the subs are, if they are 8 ohm you could wire them down to 4 ohm or if they 4 ohm u could wire them to 2 ohm, i have a 600.1 Boss amp and subs are wired together at 2 ohm and they BANG.
Are kicker L7s good speakers and what kind of amp do I need to power 2-15 inch subs?
Yes, the L-7s are great. For the amp, you first need to find out whether the sub woofers are 2-ohm, 4-ohm, or 8-ohm. Depending on the answer to that question will determine whether or not you'll need a mono amp or a dual channel amp as well as the wattage.
Can you power a 1300 watt sub with a 1500 watt amp?
Yes, are we talking rms or max? If its rms you will have no problem. well the amp is a 1500 watt max but 350wx1 rms in 4 ohm
Your Amplifier for your 600 watt sub is cutting out The peak in the amp is 600 watts How do you get it to stop cutting out?
you ohm load is too low. raise the ohm load or buy an amp that is stable at the ohm level of the sub.
Can you use a 8 ohm 400 watt speaker on a 4 ohm 350 watt amp to play bass?
Yes, you can use an 8-ohm 400-watt speaker with a 4-ohm 350-watt amplifier to play bass. The speaker will receive less power from the amp, resulting in lower volume, but it won't damage the speaker or the amplifier. Just ensure that the overall impedance of your setup matches the amplifier's specifications to prevent any potential issues.
For your two 12 inch kicker cvt12 subs which put out 400 RMS each should you use a 750 watt or 1000 watt amp?
Did you get the 2 ohm or the 4ohm? I have a 750 mono on my single 4ohm and have no where near enough power.
How do you reduce the ohms from 4 ohm to 2 ohm ON A 1000 WATT KICKER AMP MONO BLOCK IM RUNNING 2-15 AUDIO PIPE SUBS IN A SEALED BOX. THIS QUESTION IS FOR CAR AUDIO?
put 2 speakers in series
What sub should I get for a 1100 watt mono amp can I use two and wire them together how many watts should they be?
Depends on the rms or continuous rating of the amp and at what ohm is the amp stable
Can 270 watt speakers damage a 125 watt amp?
Not unless the speakers are rated at a resistance (ohms) that is incompatible with the amp. Speakers don't generate power, the rating only tells you how much they can handle. So, speakers capable of up to 270 watts, can certainly handle 125 watts. However, if the amp is not 1-ohm stable and the speakers are 1-ohm, you could cause the amp to cut out and overheat depending on the protection mechanism of the amp.
2 channel alpine 500 watt amp hooked up to 12'' comp cvr kicker in a 98 neon why does my amp keep turning off?
probably because you got your amp bridged and its not a stable ohm load
Can you run a 2 ohm type R 12' with a 4 ohm type R 12' powered by a rockford fosgate p1000-1bd amp?
I dont think your rockford 1000 is rated for 2 ohms. You could fry the amp.
