0
What else can I help you with?
Does the Rockford Fosgate 12" sub have to have an Amplifier over 50 watts?
For optimal performance, match the amplifier's power output to the rating of your subwoofer. The Rockford Fosgate 12" starts at a 150-Watt rating.
What amp would you need for a 15 inch sub?
The amplifier you need for a 15-inch subwoofer depends on the sub's power handling specifications and impedance. Generally, a good rule of thumb is to match the amplifier's RMS power output to the subwoofer's RMS power rating, typically between 300 to 1500 watts for a 15-inch sub. Additionally, ensure the amp's impedance matches the sub's impedance (usually 2 or 4 ohms) for optimal performance. Always consider your specific subwoofer model's requirements for the best match.
What are the key features to consider when choosing a PA system subwoofer for optimal sound performance?
When choosing a PA system subwoofer for optimal sound performance, consider the power rating, frequency response, enclosure type, and portability. These features will impact the bass output, clarity, and overall quality of the sound produced by the subwoofer.
What are the key features to consider when choosing an amp head for a guitar amplifier?
When choosing an amp head for a guitar amplifier, consider the power rating, number of channels, tone shaping controls, effects loop, and compatibility with speaker cabinets.
What are the key features to consider when choosing an amplifier head for a guitar setup?
When choosing an amplifier head for a guitar setup, consider the power rating, number of channels, tone shaping controls, effects loop, and overall sound quality.
What size of an amp should you get for a subwoofer in your 03 Jeep Liberty?
It depends on the power rating of the subwoofer.
What are the key features to consider when choosing a tube amp head for a guitar amplifier?
When choosing a tube amp head for a guitar amplifier, consider the power rating, number of channels, tone shaping controls, effects loop, and overall build quality. These features will impact the sound, versatility, and durability of the amplifier.
How much bass to blow a sub woofer?
Blowing a subwoofer typically occurs when it is subjected to excessive power and low frequencies that exceed its handling capacity. Bass frequencies below 30 Hz can be particularly damaging if played at high volumes. Generally, it's essential to ensure that the amplifier's power rating matches or is below the subwoofer's RMS rating and to avoid pushing the volume to the point of distortion, which can cause damage. Properly tuning the system and using a high-pass filter can help protect the subwoofer from being blown.
Will a 1200 watt amplifier blow out a 1000 watt subwoofer?
Technically, yes. Practically, no. Amplifiers and speakers are rated by the maximum amount of power (and at what impedance) they can handle. A 1200 watt amplifier will eventually destroy a 1000 watt speaker if it is operated at maximum power. In normal use, however, you rarely even get close to maximum rating.
Can you use a bigger sub with your surround sound. It's amp'd but only a cheap 100W system off ebay. Don't want there to be any clipping but the only sub I have is 750W will it work or will I blow it?
You can certainly use any subwoofer that has its own amplifier with your surround sound system, if the only signal you send it is the sub line out from the receiver. The power rating of the subwoofer gives you a good indication of the volume balance that you can expect. If you have a 5.1 receiver that is rated at 400 watts total power, your subwoofer should have a power rating of at least half of that for itself.
Is 1 farad capacitor enough for 1000 watts pioneer sub woofer?
It depends on the power rating of the amplifier. The rule of thumb is often said to be 1000 RMS watts per farad. RMS watts is basically the average output of your amp/subwoofer. The power ratings most often given by manufacturers are Peak Watts, ie. how much power the amp/sub can take before breaking down. The RMS wattage is often about half of your Peak rating. So, given that you are running your 1000w Peak Pioneer subwoofer on a 1000w Peak amplifier, and given that both of them are 500w RMS, yes, a 1 farad capacitor would give the amplifier enough juice to run the sub.
What is the best kind of amp to just power a sub?
Subwoofers draw a lot of current when played at louder volumes. Thus it is either preferable to use an amplifier which can produce as much RMS (not peak) power as the subwoofer's power rating, or to be sure not to overdrive the amplifier since this produces audio distortion. Audio distortion can burn out the voice coil within a speaker.
