answersLogoWhite

0

With my Forenza , Sometimes when backing the check engine light will come on and stay on ,and the car runs rough as it is low on power . After Turing it on and off a few times , the check engine light will turn off and the car will run normal . What's the cause of this .

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you reset a 2006 suzuki Forenza check engine light?

The easiest way to reset the 2006 Suzuki check engine light is to remove the fuse. Keep the fuse out for 10 seconds, and replace it to its original slot.


Where is the plug to check the transmission fluid on a 2007 Suzuki Forenza?

Its under the car


Were is the trasmision dipstick on forenza suzuki 2007?

There is no dipstick you have to check it under the car


Where is transmission dipstick on 2010 suzuki forenza?

The transmission dipstick on a 2010 Suzuki Forenza is located near the back of the engine compartment, typically on the passenger side. It is usually marked with a colored handle, often yellow or orange, for easy identification. To check the transmission fluid level, ensure the vehicle is on a level surface and the engine is running, then pull out the dipstick, wipe it clean, reinsert it, and check the fluid level.


How you change the oil pump in the engine in suzuki forenza?

To change the oil pump in a Suzuki Forenza, first, disconnect the battery and drain the engine oil. Remove the oil pan by unbolting it, then detach the oil pump from the engine block. Install the new oil pump, ensuring the gasket is properly seated, then reattach the oil pan and refill with fresh oil. Finally, reconnect the battery and start the engine to check for leaks.


How many motor mounts on suzuki forenza 2007?

The 2007 Suzuki Forenza typically has three motor mounts: one engine mount and two transmission mounts. These mounts help secure the engine and transmission to the vehicle's frame while minimizing vibrations. It's important to check the condition of these mounts, as worn or damaged mounts can affect vehicle performance and comfort.


Why wont my 2005 suzuki forenza start but the engine turns over?

If your 2005 Suzuki Forenza is turning over but not starting, it could be due to several issues. Common causes include a lack of fuel reaching the engine, a faulty spark plug or ignition coil, or issues with the fuel pump or fuel filter. Additionally, check the battery and connections, as weak power can prevent the engine from starting properly. If you're unable to diagnose the issue, consider consulting a mechanic for a thorough inspection.


Where do you check the transmission fluid for a 2007 suzuki forenza?

the 2007 suzuki does not have a dip stick you must take it to a professional to get transmission fluid checked.


2006 suzuki forenza shakes only when speed reaches 50mph?

Check the air pressure in your tires


How to time cams on suzuki forenza 2.0 engine?

To time the cams on a Suzuki Forenza with a 2.0 engine, first ensure the engine is at top dead center (TDC) on the compression stroke for cylinder one. Align the timing marks on the camshaft sprockets with the markings on the timing cover or the engine block. Install the timing belt, ensuring it is properly tensioned, and rotate the engine by hand to verify that all timing marks remain aligned. Finally, double-check the alignment before starting the engine to prevent any potential damage.


What is the spark plug gap for a 2004 forenza?

The spark plug gap for a 2004 Suzuki Forenza is typically set at 0.040 inches (1.0 mm). It's important to check the owner's manual or specifications for your specific engine, as variations may exist based on the engine type or modifications. Always ensure the gap is adjusted correctly for optimal engine performance.


How do you check the transmission oil suzuki forenza?

To check the transmission oil in a Suzuki Forenza, first ensure the vehicle is on a level surface and the engine is running at normal operating temperature. Locate the transmission dipstick, usually found near the back of the engine bay, and remove it. Wipe it clean, reinsert it fully, and then remove it again to check the fluid level, which should be within the designated marks. If necessary, add the appropriate type of transmission fluid through the dipstick tube until the correct level is reached.