answersLogoWhite

0

Oil pressure isn't really a function of the oil. There are several things that could make you have low oil pressure, but they're pretty much all mechanical defects in the engine itself, and adding stuff to the oil won't help because the oil itself isn't the problem.

User Avatar

Wiki User

11y ago

What else can I help you with?

Related Questions

Low oil pressure in a 1995 oldmobile aurora?

ck oil pressure with gauge, if ok replace oil sending unit there is also a $20.00 dollars oil pressure sensor that sits underneath the engine by the oil pan area(front), this sensor can get old and display the wrong pressure in the system.


What psi of oil pressure is suggested on a 350 engine at idle and cruising speed?

If everything is working properly, the oil pressure will be controlled by a "bypass" valve inside the engine. Once the oil pump builds enough pressure, any additional volume is "dumped" back into the crankcase so that the oil lines don't build up too much pressure and damage the bearings and oil pump.When the engine is cold, you should see the MAXIMUM oil pressure. Start the engine, watch the oil pressure and see where it goes. The needle will rise rapidly until the bypass valve starts dumping excess oil. Wherever the needle stops, that's your normal oil pressure. Usually it's somewhere in the middle of the gauge, 40 to 60 psi, but the exact number isn't critical. What's important is keeping it in that range... wherever the bypass takes over. If the engine warms up and the oil pressure starts to go down, you have worn bearings. That's the most common reason for a loss of oil pressure in the 350 engine. It's a great old engine, as tough as they get. If the oil pressure is starting to go down when the engine is warm, just change to a heavier grade oil at your next oil change. If you've been using 5W15, change to 10W30 or even heavier. That will help you get a lot more life out of the engine. The thicker oil will keep the worn bearings lubricated better and help the engine last longer.


Oil pressure dropped dramatically on my 1997 ford expedition is it the oil pump?

Yes, Change the oil pump... If the oil pump stopped working, severe engine damage is likely. A new/ rebuilt engine may be necessary. The only way to tell for sure is to tear down and inspect the old engine.


How much oil pressure should a 1982 Chevy 350 have?

The old rule of thumb used to be 10 lbs per 1000 rpms. So, if that old Chevy small block engine is warmed up and idling with 10 lbs of oil pressure, don't worry about it.


Where should the oil pressure for a warm 3800 v6 engine sit?

Generally for every 1000 RPM you should have 10 PSI oil pressure. Before I would get alarmed, I would replace the oil switch for you gauge as these can give you a false low reading when they are old.


How do you replace the oil switch on a 3.0 duratec dohc?

To replace the oil pressure switch on a 3.0 Duratec DOHC engine, first, ensure the engine is cool and disconnect the battery. Locate the oil pressure switch, typically found near the oil filter on the engine block. Use a socket or wrench to carefully unscrew the old switch, then apply some oil to the threads of the new switch before installing it. Finally, reconnect the electrical connector and the battery, and check for leaks by starting the engine.


Why does the oil pressure light come on when the engine idles but turn off the instant you hit the gas?

oil pressure is created by the oil pump, which is driven mechanically as the engine turns, and the faster it revs the harder it pumps. It should deliver enough pressure at idle for the light to stay off. Your problem is either a worn oil pump or your oil is too thin and needs changing. If you have an old engine, put in a heavier oil. Penrite 50 is good. Hi another possibility is your idle is set too low Also, you could have a bad or weak pressure release valve in your oil pump. (AKA bypass valve). In addition, if the oil has not been changed in a long time the oil filter may be filled with sludge reducing the pressure. Changing the oil and filter first to heavier oil is a good first step. Your engine bearings may be worn and letting too much oil escape, resulting in low pressure when the oil pump is running slower (when the engine is running at idle). Revving the engine too high can cause damage to the rod bearings and allow oil to escape too easily. If your engine has a lot of miles on it, or if it has been run without changing the oil regularly, your engine will have a lot of wear. The oil pump, main bearings, rod bearings, and camshaft bearings may all have a lot of wear on them allowing the oil to easily escape without allowing pressure to build up. Rebuilding your engine may be needed. But try changing the oil pump first.


What kind of oil should you use in your 91 sentra?

you should use 10W-30 of any reputable brand of oil. With a car that old, I would also add an oil additive like Slick 50 or similar for older engines. They cost a lot, but definitely keep your engine running smoothly.


How do you replace the oil pressure switch on a 2000 Nissan Xterra?

To replace the oil pressure switch on a 2000 Nissan Xterra, start by ensuring the engine is cool and disconnect the negative battery cable. Locate the oil pressure switch, typically found near the oil filter on the engine block. Use a socket wrench to remove the old switch, then install the new one by tightening it securely and reconnecting the electrical connector. Finally, reconnect the battery cable and check for leaks after starting the engine.


How do you change the oil pressure switch on a 2007 Chevy Colorado 3.7?

To change the oil pressure switch on a 2007 Chevy Colorado 3.7, first, ensure the engine is cool and disconnect the negative battery cable. Locate the oil pressure switch on the engine block, usually near the oil filter. Remove the electrical connector and use a socket to unscrew the old switch. Install the new switch, reconnect the electrical connector, and reconnect the battery before starting the engine to check for leaks.


How do you change a oil pressure switch on vauxhall corsa 04 plate?

To change the oil pressure switch on a 2004 Vauxhall Corsa, first, ensure the engine is cool and disconnect the battery. Locate the oil pressure switch, typically found near the oil filter on the engine block. Remove the electrical connector and unscrew the old switch using a suitable socket or wrench. Install the new switch, reconnect the connector, and reattach the battery before starting the engine to check for leaks.


How do you replace oil pressure switch on 1995 Ford F-150 with 5.0 engine?

To replace the oil pressure switch on a 1995 Ford F-150 with a 5.0 engine, first, disconnect the negative battery cable to ensure safety. Then, locate the oil pressure switch, which is typically located near the oil filter on the engine block. Use a socket wrench to remove the old switch, and install the new one by tightening it securely. Finally, reconnect the electrical connector and the battery cable before starting the engine to check for leaks.