answersLogoWhite

0

Yes, it is normal for the low range button to flash for a few seconds when you start the engine on your ML270. This typically indicates that the vehicle's system is performing a self-check to ensure that the low range function is operating correctly. Once the system confirms everything is functioning properly, the light will turn off. If the light stays on or flashes continuously after that initial period, it may indicate a problem that needs further investigation.

User Avatar

AnswerBot

1mo ago

What else can I help you with?

Related Questions

How do you change the time on the clock in the peugeot 206?

Press left button for about 2 seconds until display flashes - should be language. Press again and hours on clock will flash. Press right button to increment hours; press and hold to cycle through lots. When hours set, press left button again; minutes will flash. Press right button to increment minutes. When done, leave for about 10 seconds and display will revert to normal and save changes.


What is the red flashing wrench mean when i first start my 2006 Volkswagen Jetta TDI It does not stay on it only flashes for a few seconds and then turns off?

The red flashing ranch is an indication that the oil pressure is low. The oil pressure is at zero pounds per square inch until the engine begins to run. Within a few seconds the oil pressure is at a normal level.


Is hot flashes and nausea normal on birth control pills?

Nausea is common with a lot of women on birth control. As for hot flashes that's not normal something you should probably get checked out by your doctor.


Why does the Theft light on the console blinks every 2 - 3 seconds when the engine is off?

This is normal on most vehicles.


How do I reset the dash on my HD Sportster after battery change?

To reset the dash on your HD Sportster after a battery change, first, turn the ignition to the "On" position without starting the engine. Then, press and hold the trip reset button on the speedometer until the odometer flashes and resets. Release the button, and the dash should return to normal operation. If you're experiencing any issues, consult your owner's manual for specific instructions related to your model.


How do you do a hard reboot on a RCA Android tablet?

Press the volume up or down button and the power button at the same time, and hold it for a few seconds until the tablet turns off. Then, you can power it back on as normal.


How do you change time in sonata 7949pp01?

Press the mode button to get the time you want to change on the display. The press and hold the reset button until the seconds begin to flash>press the stop/start button to reset the seconds >press mode button to get hours to flash>press the st/stp button to advance the hours > press the reset button to get minutes to flash>advance minutes with st/stp button >press reset button to get date to flash > press st/stp button to advance date >when all time and date are set press mode to return to normal time display


Is texting on ks360 slow?

no waaaaay!!!!!!!!! its a 100 times QUICKER!!!! coz it has all the buttons you go straight from button to button from word to word in less than 10-15 seconds!!!!!! it is soo quick!! not slow like normal phones


How do you set time on casio wr50m watch?

To set the time on a Casio wr50m watch, select normal time view from the mode button. Press the adjust button, and seconds begin to flash. Adjust the time with the start/stop button. Switch from seconds, minutes, and hours with the mode button. When the time displays correctly, press the bottom adjust button to set the time.


98 Mercury Grand Marquis On steep inclines cruise running the check engine light flashes and the engine struggles When the car levels off it goes back to normal Tank had plenty of gas?

Most likely clogged fuel filter. Replace filter


How do you reset low tire pressure light on a 2003 Pontiac Bonneville?

On the dash to the right of the DIC screen there are three buttons, Mode, Select, and Reset. First, push the Select button until the DIC shows the screen for Tire Pressure, once there hold the Reset button for five seconds. While holding the Reset button for five seconds the DIC screen will go from Low Tire, to xxx, release the button and it should now show Normal.


How do you turn the controls from Button 1 to the normal controls in minecraft?

Button 1 is the left mouse button, which is normal. If you want to change it, go to the options.